Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: Sunload Sensor

Nissan Sentra B18 (2020-2025) Service Manual / Ventilation, Heater & Air Conditioner / Heater & Air Conditioning Control System :: Automatic Air Conditioner / Dtc/circuit Diagnosis / Sunload Sensor

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK SUNLOAD SENSOR SIGNAL

      1. Ignition switch ON.

      2. Check voltage between A/C auto amp. harness connector.

        A/C auto amp.

        Voltage

        (Approx.)

        Connector

        Terminals

        +

        -

        M34

        47

        78

    Is the inspection result normal?

    YES >>

    Inspection End.

    NO >>

    GO TO 2.

  2. CHECK SUNLOAD SENSOR POWER SUPPLY

      1. Ignition switch OFF.

      2. Disconnect sunload sensor connector.

      3. Ignition switch ON.

      4. Check voltage between sunload sensor harness connector and ground.

        +

        −

        Voltage

        (Approx.)

        Sunload sensor

        Connector

        Terminal

        M70

        1

        Ground

        5 V

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 5.

  3. CHECK SUNLOAD SENSOR GROUND CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect A/C auto amp. connector.

      3. Check continuity between sunload sensor harness connector and A/C auto amp. harness connector.

        Sunload sensor

        A/C auto amp.

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M70

        2

        M34

        78

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair harness or connector.

  4. REPLACE SUNLOAD SENSOR

    1. Replace sunload sensor. Refer to Removal and Installation.

    Is the inspection result normal?

    YES >>

    Inspection End.

    NO >>

    Replace A/C auto amp. Refer to Removal and Installation.

  5. CHECK SUNLOAD SENSOR POWER SUPPLY CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect A/C auto amp. connector.

      3. Check continuity between sunload sensor harness connector and A/C auto amp. harness connector.

        Sunload sensor

        A/C auto amp.

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M70

        1

        M34

        47

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair harness or connector.

  6. CHECK SUNLOAD SENSOR POWER SUPPLY CIRCUIT FOR SHORT

      1. Check continuity between sunload sensor harness connector and ground.

        Sunload sensor

        —

        Continuity

        Connector

        Terminal

        M70

        1

        Ground

        No

      2. Check voltage between sunload sensor harness connector and ground.

        +

        −

        Voltage

        (Approx.)

        Sunload sensor

        Connector

        Terminal

        M70

        1

        Ground

        0 V

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair harness or connector.

Door Motor Circuit
Diagnosis Procedure Diagnosis Procedure Note: If all of door motor DTCs are detected, check this circuit. CHECK DOOR MOTOR POWER SUPPLY ...

Intake Sensor
Diagnosis Procedure Diagnosis Procedure CHECK INTAKE SENSOR Ignition switch OFF. Remove i ...

Other materials:

Diagnosis System [chassis Control Module (with Built in Steering Angle Sensor)]
Consult Function CONSULT Function APPLICATION ITEMS CONSULT can display each diagnostic item using the diagnostic test modes as follows. Diagnosis mode CGW Status ...

Special Service Tools
Special Service Tools The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description ...

Dtc Diagnosis Procedure
DTC Diagnosis Procedure CHECK VEHICLE SPECIFICATION Check vehicle specification. >> GO TO 2. PERFORM SELF DIAGNOSTIC RESULT Ignition switch ON. ...

© 2014-2026 Copyright www.nisentra.com