Dtc Description

DTC Description

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connectors

  • Battery current sensor input signal (temperature) circuit is shorted (Ground)

• Battery current sensor

FAIL-SAFE

—

Confirmation Procedure

Confirmation Procedure

1. PERFORM COMPONENT FUNCTION CHECK

   1. CONSULT

      1. Ignition ON, and wait for 5 seconds or more.

      2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

   Is the inspection result normal?

   YES>>

   To check malfunction symptom before repair: Refer to Intermittent Incident.

   YES>>

   Confirmation after repair: Inspection End.

   NO>>

   Refer to DTC Diagnosis Procedure.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

1. CHECK BATTERY CURRENT SENSOR POWER

   1. 1. Ignition switch OFF.

      2. Disconnect battery current sensor connector.

      3. Ignition switch ON.

      4. Check the voltage between battery current sensor harness connector and ground.

         (+)		(-)	Voltage (Approx.)
         Battery current sensor
         Connector	Terminal
         E39	4	Ground	4 – 6 V

   Is the inspection result normal?

   YES >>

   GO TO 3.

   NO >>

   GO TO 2.

2. CHECK BATTERY CURRENT SENSOR POWER CIRCUIT

   1. 1. Ignition switch OFF.

      2. Disconnect IPDM E/R connector.

      3. Check the continuity between battery current sensor harness connector and IPDM E/R harness connector.

         Battery current sensor		IPDM E/R		Continuity
         Connector	Terminal	Connector	Terminal
         E39	4	F98	95	Yes

      4. Check the continuity between battery current sensor harness connector and ground.

         Battery current sensor		—	Continuity
         Connector	Terminal
         E39	4	Ground	No

   Is the inspection result normal?

   YES >>

   Replace IPDM E/R. Refer to Removal and Installation.

   NO >>

   Repair or replace harness.

3. CHECK BATTERY CURRENT SENSOR GROUND

   1. 1. Ignition switch OFF.

      2. Check the continuity between battery current sensor harness connector and ground.

         Battery current sensor		—	Continuity
         Connector	Terminal
         E39	2	Ground	Yes

   Is the inspection result normal?

   YES >>

   GO TO 5.

   NO >>

   GO TO 4.

4. CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT

   1. 1. Disconnect IPDM E/R connector.

      2. Check the continuity between battery current sensor harness connector and IPDM E/R harness connector.

         Battery current sensor		IPDM E/R		Continuity
         Connector	Terminal	Connector	Terminal
         E39	2	F98	96	Yes

      3. Check the continuity between battery current sensor harness connector and ground.

         Battery current sensor		—	Continuity
         Connector	Terminal
         E39	2	Ground	No

   Is the inspection result normal?

   YES >>

   Replace IPDM E/R. Refer to Removal and Installation.

   NO >>

   Repair or replace harness.

5. CHECK BATTERY TEMPERATURE INPUT SIGNAL CIRCUIT 1

   1. 1. Disconnect IPDM E/R connector.

      2. Check the continuity between battery current sensor harness connector and ground.

         Battery current sensor		—	Continuity
         Connector	Terminal
         E39	3	Ground	No

   Is the inspection result normal?

   YES >>

   GO TO 6.

   NO >>

   Repair or replace harness.

6. CHECK BATTERY CURRENT SENSOR

   1. Refer to Component Inspection.

   Is the inspection result normal?

   YES>>

   Refer to Intermittent Incident. If the inspection result of the connector is normal then replace IPDM E/R. Refer to Removal and Installation.

   NO>>

   Replace battery current sensor. Refer to Removal and Installation.

Component Inspection

Component Inspection

1. CHECK BATTERY TEMPERATURE SENSOR

   1. 1. Ignition switch OFF.

      2. Disconnect battery current sensor connector.

      3. Check the resistance between battery current sensor terminals.

         Battery current sensor		Resistance
         Terminals
         2	3	Continuity exists and the resistance value is 100 Ω or more

         Before measuring the terminal voltage, confirm that the battery is fully charged.

   Is the inspection result normal?

   YES >>

   Inspection End.

   NO >>

   Replace battery current sensor.