Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / P2809-00 Pressure Control Solenoid G

Nissan Sentra B18 (2020-2025) Service Manual: P2809-00 Pressure Control Solenoid G

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P2809

'PRESSURE CONTROL SOLENOID G

(Pressure Control Solenoid "G" Stuck On)

Diagnosis condition

Diagnosis is permitted when all of the following conditions are satisfied:

a) Throttle valve opening angle < 6.27 deg

b) Nissan Sentra Vehicle speed < 3 km/h (2 MPH)

c) 20 °C (68 °F) < CVT fluid temperature < 100 °C (212 °F)

d) Input speed before select N→D or N(P)→R > 500 rpm

e) Shift position: D, L or R position

f) Stay time in the P/N position for 3 sec or more just before shifting to the other positions.

Signal

—

Threshold

When all the following conditions are established three times in 1DC:

Input speed: 200 rpm or less.

Detection time after select position

– N → D	: Less than 0.4 seconds
– N → R	: Less than 0.3 seconds
– P → R	: Less than 0.3 seconds

Diagnosis delay time

—

Note:

DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF → ON → driving → OFF”.

POSSIBLE CAUSE

Harness or connector
Select soenoid valve
Control valve
TCM
Clutch-pack

FAIL-SAFE

Selector shock is large
Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V.

>>
GO TO 2.

CHECK DTC DETECTION

Start the engine.

Continue to maintain the following conditions during this procedure.

Accelerator pedal	: Released
Nissan Sentra Vehicle speed	: 0 km/h (0 MPH)
CVT fluid temperature	: 20 °C (68 °F) - 100 °C (212 °F)

Depress the brake pedal.
Shift the selector lever from "P" position to "R" position and wait for 5 seconds.
Shift the selector lever to "N" position.
Shift the selector lever to "D" posiiton and wait for 5 seconds.
Sihft the selector lever to "N" position.
Shift the selector lever to "R" position and wait for 5 seconds.
Shift the selector lever to "P" position.
Repeat step 3 to 8 two times.
Check the DTC.

Is "P2809-00" detected?

YES >>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

INSPECT CVT STEEL BELT

IInspect the CVT steel belt. Refer to Component Inspection.

Is CVT steel belt OK?
YES >>
GO TO 2.
NO >>
GO TO 4.

CHECK SELECT SOLENOID VALVE CIRCUIT - 1

Disconnect TCM harness connector.
Disconnect CVT unit harness connector.

Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Resistance
Connector	Terminal	Connector	Terminal	Resistance
F23	37	F46	4	1 Ω or less

Is the inspection result normal?

YES >>

GO TO 3.

NO >>

Repair harness or connector.

REPLACE CONTROL VALVE

Replace control valve. Refer to Removal and Installation.

>>
GO TO 6.

CHECK SELECT SOLENOID VALVE CIRCUIT - 2

Disconnect TCM harness connector.
Disconnect CVT unit harness connector.

Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Resistance
Connector	Terminal	Connector	Terminal	Resistance
F23	37	F46	4	1 Ω or less

Is the inspection result normal?

YES >>

GO TO 5.

NO >>

Repair harness or connector.
GO TO 5.

REPLACE BELT AND PULLEYS

Replace belt and pulleys. Refer to Disassembly and Assembly.

>>
GO TO 6.
CHECK DTC DETECTION

Perform DTC confirmation procedure. Refer to DTC Description.

Is "P2809-00" detected again?
YES >>
Replace TCM. Refer to Removal and Installation.
NO >>
INSPECTION END

 P2808-00 Pressure Control Solenoid G

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2808 00 PRESSURE CONTROL SOLENOID G (Pressure C...

 P2812-00 Pressure Control Solenoid G

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2812 00 PC SOLENOID G (Pressure Control Solenoi...

Other materials:

Periodic Maintenance
Idle Speed Idle Speed : Periodic Maintenance IDLE SPEED : Periodic Maintenance With CONSULT Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT. Without CONSULT Attach induction type (current detection type) rev counter (A) to loop wire as sho ...

Stall Test
Work Procedure Work Procedure INSPECTION Check the engine oil level. Replenish if necessary. Refer to Inspection. Check for leak of the CVT fluid. Refer to Inspection. Drive for about 10 minutes to warm up the Nissan Sentra vehicle so that the CVT fluid temperature is 50 ...

Basic Inspection
Camshaft Valve Clearance Inspection and Adjustment Inspection and Adjustment INSPECTION Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if there is unusual engine conditions regarding valve clearance. Remove r ...