Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / P27f0-00 Transmission Range Control B Position Sensor/switch

Nissan Sentra B18 (2020-2025) Service Manual: P27f0-00 Transmission Range Control B Position Sensor/switch

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC		CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P27F0	00	T/M RANGE CTRL B POSI SEN/SW (Transmission Range Control "B" Position Sensor/Switch Circuit Range/Performance)	1	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 4 signal
				Threshold	Transmission range switch 4 status is open circuit
				Diagnosis delay time	0.3 seconds
			2	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 4 signal
				Threshold	Transmission range switch 4 status is intermediate voltage
				Diagnosis delay time	0.3 seconds

POSSIBLE CAUSE

Harness or connector
Transmission range switch
TCM

FAIL-SAFE

Shift position indicator on combination meter is not displayed
Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V.

>>
GO TO 2.
CHECK DTC DETECTION
1. Ignition switch ON.
2. Shift the selector lever to "R" position and wait for 5 seconds or more.
3. Shift the selector lever to "N" position and wait for 5 seconds or more.
4. Shift the selector lever to "D" position and wait for 5 seconds or more.
5. Shift the selector lever to "L" position and wait for 5 seconds or more.
6. Shift the selector lever to "P" position and wait for 5 seconds or more.
7. Check the DTC
Is "P27F0-00" detected?
YES >>
Proceed to Diagnosis Procedure.
NO-1>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>
Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

CHECK TRANSMISSION RANGE SWITCH 4 CIRCUIT

Check transmission range switch 4 circuit. Refer to Diagnosis Procedure.

>>
GO TO 2.
CHECK DTC DETECTION

Perform DTC confirmation procedure. Refer to DTC Description.

Is "P27F0-00" detected again?
YES >>
Replace TCM. Refer to Removal and Installation.
NO >>
INSPECTION END

 P27ef-00 Transmission Range Control B Position Sensor/switch

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P27EF 00 T/M RANGE CTRL B POSI SEN/SW (Transmiss...

 P2808-00 Pressure Control Solenoid G

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2808 00 PRESSURE CONTROL SOLENOID G (Pressure C...

Other materials:

Warning Chime System. Symptom Diagnosis
Warning Chime System Symptoms. Symptom Table Symptom Table Symptom Table CAUTION: Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected. ...

Intelligent Key System All Functions Cannot Operate (one Key)
Description Description Intelligent Key system all functions cannot operate (door lock and engine start). (One Intelligent Key has the symptom, other keys operate normally.) SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE SYMPTOM, OTHER KEYS OPERATE NORMALLY) ...

P2101 Electric Throttle Control Function
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...