Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / P27ef-00 Transmission Range Control B Position Sensor/switch

Nissan Sentra B18 (2020-2025) Service Manual: P27ef-00 Transmission Range Control B Position Sensor/switch

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC		CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P27EF	00	T/M RANGE CTRL B POSI SEN/SW (Transmission Range Control "B" Position Sensor/Switch Circuit/Open)	1	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 3 signal
				Threshold	Transmission range switch 3 status is open circuit
				Diagnosis delay time	0.3 seconds
			2	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 3 signal
				Threshold	Transmission range switch 3 status is intermediate voltage
				Diagnosis delay time	0.3 seconds

POSSIBLE CAUSE

Harness or connector
Transmission range switch
TCM

FAIL-SAFE

Shift position indicator on combination meter is not displayed
Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V.

>>
GO TO 2.
CHECK DTC DETECTION
1. Ignition switch ON.
2. Shift the selector lever to "R" position and wait for 5 seconds or more.
3. Shift the selector lever to "N" position and wait for 5 seconds or more.
4. Shift the selector lever to "D" position and wait for 5 seconds or more.
5. Shift the selector lever to "L" position and wait for 5 seconds or more.
6. Shift the selector lever to "P" position and wait for 5 seconds or more.
7. Check the DTC
Is "P27EF-00" detected?
YES >>
Proceed to Diagnosis Procedure.
NO-1>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>
Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

CHECK TRANSMISSION RANGE SWITCH 3 CIRCUIT

Check transmission range switch 3 circuit. Refer to Diagnosis Procedure.

>>
GO TO 2.
CHECK DTC DETECTION

Perform DTC confirmation procedure. Refer to DTC Description.

Is "P27EF-00" detected again?
YES >>
Replace TCM. Refer to Removal and Installation.
NO >>
INSPECTION END

 P27ec-00 Transmission Range Control a Position Sensor/switch

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P27EC 00 T/M RANGE CTRL A POSI SEN/SW (Transmiss...

 P27f0-00 Transmission Range Control B Position Sensor/switch

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P27F0 00 T/M RANGE CTRL B POSI SEN/SW (Transmiss...

Other materials:

Basic Inspection
Camshaft Valve Clearance Inspection and Adjustment Inspection and Adjustment INSPECTION Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if there is unusual engine conditions regarding valve clearance. Remove r ...

Combination Switch Output Circuit. Diagnosis Procedure
Diagnosis Procedure Diagnosis Procedure CHECK OUTPUT 1 - 6 CIRCUIT FOR OPEN Ignition switch OFF. Disconnect BCM connector and combination switch connectors. ...

Primary Pressure Solenoid Valve Circuit
Diagnosis Procedure Diagnosis Procedure CHECK HARNESS CONNECTOR Ignition switch OFF. Check the mating condition of TCM harness connector and CVT unit harness connector. Is the inspect ...