Nissan Sentra B18 (2020-2025) Service Manual: Unit Removal and Installation. Transaxle Assembly
Transaxle Assembly
Exploded View
Exploded View
|
1. |
Transaxle assembly |
A. |
Refer to Removal and Installation |
B. |
Refer to Removal and Installation |
Removal and Installation
Removal and Installation
Warning:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Do not reuse CSC (Concentric Slave Cylinder). The CSC (Concentric Slave Cylinder) slides back to the original position every time the transaxle assembly is removed. This action may allow dust or contaminants to gather on the sliding parts and damage a seal of CSC (Concentric Slave Cylinder) causing clutch fluid leakage.
Note:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spilling.
REMOVAL
Shift the shift lever to the neutral position.
Remove the engine assembly together with transaxle assembly from the Nissan Sentra vehicle. Refer to Removal and Installation.
Disconnect the park/neutral position (PNP) switch (neutral switch) harness connector.
Remove the starter motor. Refer to Removal and Installation.
Remove the clutch tube from CSC (Consentric Slave Cylinder). Refer to Exploded View.
Remove the transaxle assembly and engine assembly bolts. Refer to Exploded View.
Remove transaxle assembly from the engine assembly.
Remove engine mounting insulator (LH). Refer to Exploded View.
Remove CSC (Concentric Slave Cylinder). Refer to Removal and Installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
-
When replacing an engine or transaxle you must make sure any dowels are installed correctly during re-assembly
-
The transaxle assembly must not interfere with the wire harnesses and clutch tube.
-
Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of drive train components.
-
When installing transaxle assembly, do not bring input shaft into contact with clutch cover.
-
Tapping work for tapping bolts is not applied to new transaxle case. Do not perform tapping by other than screwing tapping bolts because tapping is formed by screwing tapping bolts into transaxle case.
Tighten transaxle assembly mounting bolts to the specified torque. As shown viewing from the engine.
|
Bolt symbol |
(A) |
(B) |
|---|---|---|
|
Insertion direction |
Transaxle to engine |
Engine to transaxle |
|
Quantity |
3 |
6 |
|
Bolt length “ |
60 (2.36) |
50 (1.97) |
|
Tightening torque N·m (kg-m, ft-lb) |
62.0 (6.3, 46) |
|
” mm (in)
Inspection
Inspection
Check the operation of the control linkage. Refer to Inspection.
Check the oil level and for oil leaks. Refer to Inspection.
Other materials:
Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit)
Abs Actuator and Electric Unit (control Unit)
Values on the Diagnosis Tool
Values on the
Diagnosis Tool
Note:
The following table includes information (items)
inapplicable to this Nissan Sentra vehicle: For information (items) applicable to
this vehicle, refer to CONSULT display ...
B1019 Occupant Sens
Dtc Description
DTC Description
DESCRIPTION
B1019 OCCUPANT SENS
The OCS control unit is wired to the air bag
diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the OCS for failures and interruptions in communication
between the OCS control unit and the air bag ...
License Plate Lamp Circuit
Component Function Check
Component Function
Check
CHECK TAIL LAMP LH OPERATION
Check that tail lamp LH is turned ON when lighting
switch is turned 1ST.
Is the inspection result normal?
YES >>
GO TO 2.
...