Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: License Plate Lamp Circuit

Nissan Sentra B18 (2020-2025) Service Manual / Driver Controls / Exterior Lighting System :: Halogen Headlamp / Dtc/circuit Diagnosis / License Plate Lamp Circuit

Component Function Check

Component Function Check

  1. CHECK TAIL LAMP LH OPERATION

    1. Check that tail lamp LH is turned ON when lighting switch is turned 1ST.

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    Refer to Component Function Check.

  2. CHECK LICENSE PLATE LAMP OPERATION

    1. CONSULT

      1. Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R”.

      2. With operating the test item, check that the license plate lamp is turned ON.

        On

        : License plate lamp ON

        Off

        : License plate lamp OFF

    Is the inspection result normal?

    YES >>

    License plate lamp circuit is normal.

    NO >>

    Refer to Diagnosis Procedure.

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK LICENSE PLATE LAMP BULB

    1. Check the license plate lamp bulb. Refer to Component Inspection.

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    Replace corresponding license plate lamp. Refer to Removal and Installation.

  2. CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

      1. Ignition switch OFF.

      2. Disconnect the following connectors:

        • IPDM E/R

        • Rear combination lamp LH (body side)

        • Rear combination lamp LH (trunk lid side)

        • License plate lamp LH

        • License plate lamp RH

      3. Check continuity between IPDM E/R harness connector and license plate lamp harness connector.

        IPDM E/R

        License plate lamp

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        RH

        E47

        4

        B89

        1

        Yes

        LH

        B91

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Repair or replace harness.

  3. CHECK LICENSE PLATE LAMP GROUND CIRCUIT

    1. Check continuity between license plate lamp harness connector and ground.

      License plate lamp

      —

      Continuity

      Connector

      Terminal

      RH

      B89

      2

      Ground

      Yes

      LH

      B91

    Is the inspection result normal?

    YES >>

    Replace corresponding license plate lamp. Refer to Removal and Installation.

    NO >>

    Repair or replace harness.

Tail Lamp Circuit
Component Function Check Component Function Check CHECK TAIL LAMP OPERATION CONSULT Select “TAIL LAMP” in “Ac ...

Turn Signal Lamp Circuit
Component Function Check Component Function Check CHECK TURN SIGNAL LAMP OPERATION CONSULT Select “FLASHER” in ...

Other materials:

Brake pedal
Inspection BRAKE PEDAL HEIGHT Check the brake pedal height (H1) between the dash lower panel (1) and the brake pedal upper surface. Brake pedal height (H1) : Refer to BR-54, "Brake Pedal". CAUTION: Check the brake pedal height with the floor trim removed. STOP LAMP SWITCH AND BR ...

Wiring Diagram
Wiring Diagram BATTERY POWER SUPPLY Refer to Wiring Diagram. BATTERY POWER SUPPLY FUSE NO. 19 Refer to Wiring Diagram. BATTERY POWER SUPPLY FUSE NO. 40 Refer to Wiring Diagram. IGNITION POWER SUPPLY Refer to Wiring Diagram. IGNITION POWER SUPPLY FUSE NO. 48 Refer to Wiring Diagra ...

Controls
Fan control dial The fan control dial turns the fan on and off, and controls fan speed. Air flow control buttons The air flow control buttons allow you to select the air flow outlets. MAX — Air flows from center and side A/Cvents with maximum cooling. — Air flows from center and side v ...

© 2014-2026 Copyright www.nisentra.com