Nissan Sentra B18 (2020-2025) Service Manual: Symptom Diagnosis
Exterior Lighting System Symptoms
Symptom Table
Symptom Table
Note:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.
|
Symptom |
Possible cause |
Inspection item |
|
|---|---|---|---|
|
Headlamp (HI) is not turned ON |
One side |
|
Headlamp (HI) circuit Refer to Component Function Check. |
|
LED headlamp circuit Refer to Diagnosis Procedure. |
||
|
Both sides |
Symptom diagnosis “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON” Refer to Diagnosis Procedure. |
||
|
High beam indicator lamp is not turned ON [headlamp (HI) is turned ON] |
Combination meter |
“METER/M&A” “Data Monitor” “HI-BEAM IND” |
|
|
Headlamp (LO) is not turned ON |
One side |
|
Headlamp (LO) circuit Refer to Component Function Check. |
|
LED headlamp circuit Refer to Diagnosis Procedure. |
||
|
Both sides |
Symptom diagnosis “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON” Refer to Diagnosis Procedure. |
||
|
Each lamp is not turned ON/OFF with lighting switch AUTO |
|
Combination switch Refer to Symptom Table. |
|
|
Optical sensor circuit Refer to Component Function Check. |
||
|
Parking lamp is not turned ON |
|
Parking lamp circuit Refer to Component Function Check. |
|
|
Tail lamp and front side marker lamp is not turned ON |
|
Tail lamp circuit Refer to Component Function Check. |
|
|
License plate lamp is not turned ON |
|
License plate lamp circuit Refer to Component Function Check. |
|
|
Parking lamp, license plate lamp, side marker lamp and tail lamp are not turned ON |
Symptom diagnosis “PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT TURNED ON” Refer to Diagnosis Procedure. |
||
|
Position light indicator lamp is not turned ON (parking lamp, license plate lamp, side marker and tail lamp are turned ON) |
Combination meter |
“METER/M&A” “Data Monitor” “LIGHT IND” |
|
|
Daytime running light is not turned ON |
|
Daytime running light circuit Refer to Component Function Check. |
|
|
Turn signal lamp does not blink |
Indicator lamp is normal (all of turn signal lamp is not blinks) |
|
Turn signal lamp circuit Refer to Component Function Check. |
|
Indicator lamp is normal (applicable side performs high flasher activation) |
|
||
|
Indicator lamp is included |
|
Combination switch Refer to Symptom Table. |
|
|
Turn signal indicator lamp does not blink (turn signal lamp is normal) |
One side |
Combination meter |
— |
|
Both sides (always) |
|
“METER/M&A” “Data Monitor” “TURN IND” |
|
|
Both sides (only when activating hazard warning lamp with ignition switch OFF) |
|
Combination meter Power supply and ground circuit Refer to Diagnosis Procedure (type A). Refer to Diagnosis Procedure (type B). |
|
|
|
Hazard switch circuit Refer to Component Function Check. |
|
|
Stop lamp and high-mounted stop lamp are not turned ON |
All of stop lamp and high-mounted stop lamp are not turned ON |
|
Stop lamp circuit Refer to Component Function Check. |
|
Any of stop lamp and high-mounted stop lamp are not turned ON |
|
||
|
Back-up lamp is not turned ON (with CVT) |
|
TCM Power supply and ground circuit Refer to Diagnosis Procedure. |
|
|
Transmission range switch circuit Refer to Diagnosis Procedure. |
||
|
Back-up lamp relay circuit Refer to Component Function Check. |
||
|
Headlamp warning stays ON |
|
Headlamp warning circuit Refer to Component Function Check. |
|
|
HBA is not turned ON/OFF |
|
Combination switch Refer to Symptom Table. |
|
Both Side Headlamps (hi) Are Not Turned on
Diagnosis Procedure
Diagnosis Procedure
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
-
COMBINATION SWITCH INSPECTION
-
Check combination switch. Refer to Symptom Table.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning part.
-
-
CHECK HIGH BEAM REQUEST SIGNAL
-
CONSULT-
Select “HIGH BEAM REQ” and “PASSING REQ” in “Data Monitor” mode of “IPDM E/R”.
-
With operating the lighting switch, check the monitor status.
Monitor item
Condition
Monitor status
HIGH BEAM REQ
Lighting switch
(2ND)
HI
On
LO
Off
PASSING REQ
Lighting switch
PASS
On
OFF
Off
-
Is the inspection result normal?
YES>>Replace IPDM E/R. Refer to Removal and Installation.
NO>>Replace BCM. Refer to Removal and Installation.
-
Normal Operating Condition
Description
Description
LED HEADLAMP
-
LED brightness and color may slightly change until the temperature becomes stable. This is not malfunction.
-
Illumination time lag may occur between right and left. This is not malfunction.
-
Brightness may be reduced due to aged deterioration of LED.
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel, sky bridge, shadowed area etc.) while using the auto light system. This causes for the control difference. This is normal.
HIGH BEAM ASSIST SYSTEM
When driving while using the high beam assist system, the headlamp beam may not switch or the beam switching timing may vary according to the ambient environment (the condition of the Nissan Sentra vehicle ahead, the condition of the road, the position of the vehicle, etc.). This is due to control differences and is not a malfunction.
Other materials:
Seat. System Description
Component Parts
Power Seat System
Component Parts Location
Component Parts
Location
No.
Component
Function
1.
...
Diagnosis System (intelligent Key). Intelligent Key
Intelligent Key
Consult Function (intelligent Key Unit)
CONSULT Function (INTELLIGENT KEY UNIT)
SELF DIAGNOSTIC RESULT
Refer to DTC Index.
DATA MONITOR
Note:
The following table includes information (items)
inapplicable to this Nissan Sentra vehicle. For information (items) appl ...
Precaution. Precautions
Precautions
Precaution for Supplemental Restraint System (srs) "air Bag" and "seat Belt Pre-Tensioner"
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as
“AIR BAG” and “SEAT BELT PRE-TENSIONER”,
u ...