Nissan Sentra B18 (2020-2025) Service Manual: Removal and Installation
Av Control Unit
Exploded View
Exploded View
|
1. |
AV control unit bracket (LH) |
2. |
AV control unit |
3. |
AV control unit bracket (RH) |
Removal and Installation
Removal and Installation
REMOVAL
CAUTION:
When replacing AV control unit, perform "ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT". Refer to Description.
Disconnect the negative battery terminal. Refer to Battery Disconnect.
Remove cluster lid C. Refer to Removal and Installation
Remove the AV control unit screws, then pull out the AV control unit.
Disconnect the harness connectors from the AV control unit and remove.
If necessary, remove the AV control unit bracket (LH/RH) screws and the AV control unit brackets (LH/RH).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When replacing AV control unit, perform "ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT". Refer to Description.
Steering Switches
Exploded View
Exploded View
|
1. |
Steering wheel |
2. |
Steering wheel finisher |
3. |
Steering switches |
Removal and Installation
Removal and Installation
REMOVAL
Note:
The steering switches are serviced as an assembly.
Remove driver air bag. Refer to Removal and Installation.
Using a
suitable tool, release pawls on the steering wheel front finisher
(1) using suitable tool and remove from the steering wheel.
|
|
: Pawl |
Using a
suitable tool, release pawls on the steering switches (1) using
suitable tool and remove from the steering wheel.
|
|
: Pawl |
Disconnect steering switch connector from spiral cable and remove from Nissan Sentra vehicle.
INSTALLATION
Installation is in the reverse order of removal.
Microphone
Removal and Installation
Removal and Installation
REMOVAL
Remove the front room/map lamp assembly. Refer to Removal and Installation.
Using a
suitable tool, release pawls and remove microphone (1) from the
front room/map lamp assembly. 
|
|
: Pawl |
INSTALLATION
Installation is in the reverse order of removal.
Front Auxiliary Input Jacks
Removal and Installation
Removal and Installation
REMOVAL
Remove cluster lid C. Refer to Removal and Installation.
Using a
suitable tool, release pawls on the front auxiliary input jacks
(1), then remove from the front of cluster lid C (2). 
|
|
: Pawl |
INSTALLATION
Installation is in the reverse order of removal.
Front Door Speaker
Exploded View
Exploded View
|
1. |
Front door speaker |
Removal and Installation
Removal and Installation
REMOVAL
Remove front door finisher. Refer to Removal and Installation.
Remove front door speaker bolts, then pull out front door speaker.
Disconnect the harness connector from front door speaker and remove.
INSTALLATION
Installation is in the reverse order of removal.
Antenna Amp
Removal and Installation
Removal and Installation
Removal
Remove passenger side rear pillar finisher. Refer to Removal and Installation — Rear Pillar Upper Finisher.
Remove
screw (A) from antenna amp (1). 
Disconnect the harness connector and remove the antenna amp.
Installation
Installation is in the reverse order of removal.
Other materials:
Rear Automatic Braking (RAB)
WARNING
Failure to observe all warnings and instructions for the proper use of the
Rear Automatic Braking (RAB) system may result in serious injury or death.
The RAB system on the Nissan Sentra is a driver assistance feature only.
It does not replace safe driving practices.
Always check ...
P0222 Tp Sensor
Dtc Description
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis
content)
DTC detection
condition
...
Brake Fluid
Draining
Draining
CAUTION:
Before working, place the ignition switch in the
OFF position and disconnect the harness connector from the ABS
actuator and electric unit (control unit) or the negative battery
terminal. Refer to Battery Disconnect ...