S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P0222 Tp Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0222

TP SEN 1/CIRC-B1

(Throttle/Pedal position sensor/switch “B” circuit low)

Diagnosis condition

Engine running at idle

Signal (terminal)

TP sensor 1 signal

Threshold

An excessively low voltage from the TP sensor 1 is sent to ECM

Diagnosis delay time

—

POSSIBLE CAUSE

  • Harness or connectors (TP sensor 1 circuit is open or shorted.)

  • Electric throttle control actuator (TP sensor 1)

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode

Fail safe mode

Nissan Sentra Vehicle behavior

Device fix mode

  • This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position.

  • The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).

Others

The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 degrees.

The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the acceleration will be poor.

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

  1. CHECK DTC PRIORITY

    If DTC P0222 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

    Is applicable DTC detected?

    YES >>

    Perform diagnosis of applicable. Refer to DTC Description.

    NO >>

    GO TO 2.

  2. PRECONDITIONING

    If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is 8 V or more at idle.

    >>

    GO TO 3.

  3. PERFORM DTC CONFIRMATION PROCEDURE

    1. Start the engine and let it idle for 1 second.

    2. Check DTC.

    Is DTC detected?

    YES >>

    Proceed to DTC Diagnosis Procedure.

    NO-1 >>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2 >>

    Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK DTC PRIORITY

    If DTC P0222 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

    Is applicable DTC detected?

    YES >>

    Perform diagnosis of applicable. Refer to DTC Description.

    NO >>

    GO TO 2.

  2. CHECK THROTTLE POSITION (TP) SENSOR 1 POWER SUPPLY-1

    1. Turn ignition switch OFF.

    2. Disconnect electric throttle control actuator harness connector.

    3. Turn ignition switch ON.

    4. Check the voltage between electric throttle control actuator harness connector terminals.

      Electric throttle control actuator

      Voltage

      (Approx.)

      Connector

      +

      −

      Terminal

      F7

      3

      2

      5 V

    Is the inspection result normal?

    YES >>

    GO TO 7.

    NO >>

    GO TO 3.

  3. CHECK TP SENSOR 1 POWER SUPPLY-2

    Check the voltage between electric throttle control actuator harness connector and ground.

    +

    −

    Voltage

    (Approx.)

    Electric throttle control actuator

    Connector

    Terminal

    F7

    3

    Ground

    5 V

    Is the inspection result normal?

    YES >>

    GO TO 5.

    NO >>

    GO TO 4.

  4. CHECK TP SENSOR 1 POWER SUPPLY CIRCUIT

    1. Turn ignition switch OFF.

    2. Disconnect ECM harness connector.

    3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

      Electric throttle control actuator

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      F7

      3

      F25

      95

      Existed

    4. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES >>

    Perform trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

    NO >>

    Repair or replace malfunctioning part.

  5. CHECK TP SENSOR 1 GROUND CIRCUIT

    1. Turn ignition switch OFF.

    2. Disconnect ECM harness connector.

    3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

      Electric throttle control actuator

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      F7

      2

      F25

      90

      Existed

    4. Also check harness for short to power.

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair or replace malfunctioning part.

  6. CHECK ECM GROUND CIRCUIT

    1. Check the continuity between ECM harness connector and ground.

      ECM

      —

      Continuity

      Connector

      Terminal

      F24

      5

      Ground

      Existed

      65

      F25

      69

      E16

      157

      159

      162

    2. Also check harness for short to power.

    Is the inspection result normal?

    YES >>

    INSPECTION END

    NO >>

    Repair or replace malfunctioning part.

  7. CHECK TP SENSOR 1 INPUT SIGNAL CIRCUIT

    1. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

      Electric throttle control actuator

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      F7

      1

      F25

      85

      Existed

    2. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES >>

    GO TO 8.

    NO >>

    Repair or replace malfunctioning part.

  8. CHECK THROTTLE POSITION SENSOR

    Refer to Component Inspection.

    Is the inspection result normal?

    YES >>

    INSPECTION END

    NO >>

    Replace malfunctioning electric throttle control actuator. Refer to Removal and Installation.

    P0201 Fuel Injector
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0201 INJECTOR CIRC-CYL1 Diagnosis condition Eng...
    P0261 Fuel Injector (cylinder 1)
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0261 CYL1 INJECTOR (Cylinder 1 Injector A Circu...

    Other materials:

    Brake Lines and Cables
    Inspection Inspection BRAKE LINE Check brake line (tubes and hoses) for cracks, deterioration or other damage. Replace any damaged parts. Check for brake fluid leaks by fully depressing brake pedal while engine is running. CAUTION: ...

    Front Disc Brake
    Inspection - Front Brake Pad Inspection - Front Brake Pad INSPECTION Check brake pad wear thickness from an inspection hole (A) on cylinder body. Wear thickness : Refer to Front Disc Brake. ...

    Rear-facing child restraint installation using LATCH
    Do not use the LATCH lower anchors if the combined weight of the child and the child restraint exceeds 65 lbs (29.5 kg). If the combined weight is greater than 65 lbs (29.5 kg), install the child restraint using the vehicle’s seat belt instead of the lower anchors. Always follow the child re ...