Nissan Sentra B18 (2020-2025) Service Manual: B24d4-08 A/c Control Comm
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC No. |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
|
|---|---|---|---|
|
B24D4-08 |
A/C CONTROL COMM (A/C control communication) |
Diagnosis condition |
Ignition switch ON |
|
Signal (Terminal) |
LIN (A/C control) signal |
||
|
Threshold |
Receive internal circuit error message from A/C switch assembly via LIN communication |
||
|
Diagnosis delay time |
2 seconds or more |
||
POSSIBLE CAUSE
-
Fuse
-
Harness and connector (A/C switch assembly circuit is open or shorted)
-
A/C switch assembly
-
A/C auto amp.
FAIL-SAFE
—
Confirmation Procedure
Confirmation Procedure
-
PERFORM SELF DIAGNOSTIC RESULT
-
CONSULT-
Ignition switch ON.
-
Select “Self Diagnostic Result� mode of “HVAC�.
-
Check DTC.
-
Is DTC detected?
YES >>Refer to DTC Diagnosis Procedure.
NO >>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>Confirmation after repair: Inspection End.
-
Dtc Diagnosis Procedure
DTC Diagnosis Procedure
-
CHECK FUSE
-
-
Ignition switch OFF.
-
Check that the following fuse is not blown (open):
Component
Location
Fuse No.
Capacity
A/C switch assembly
Fuse block (J/B)
6
10 A
-
Is the fuse blown (open)?
YES >>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO >>GO TO 2.
-
-
CHECK A/C SWITCH ASSEMBLY POWER SUPPLY
-
-
Disconnect A/C switch assembly connector.
-
Ignition switch ON.
-
Check voltage between A/C switch assembly harness connector and ground.
+
-
Voltage
(Approx.)
A/C switch assembly
Connector
Terminal
M59
5
Ground
Battery voltage
-
Is the inspection result normal?
YES >>GO TO 3.
NO >>Repair harness or connector between A/C switch assembly and fuse.
-
-
CHECK A/C SWITCH ASSEMBLY GROUND CIRCUIT FOR OPEN
-
-
Ignition switch OFF.
-
Check continuity between A/C switch assembly harness connector and ground.
A/C switch assembly
—
Continuity
Connector
Terminal
M59
7
Ground
Yes
-
Is the inspection result normal?
YES >>GO TO 4.
NO >>Repair harness or connector.
-
-
CHECK A/C SWITCH ASSEMBLY LIN SIGNAL
-
-
Connect A/C switch assembly connector.
-
Ignition switch ON.
-
Confirm output waveform between A/C switch assembly harness connector and ground with oscilloscope.
+
-
Output waveform
A/C switch assembly
Connector
Terminal
M59
8
Ground

-
Is the inspection result normal?
YES >>Replace A/C switch assembly. Refer to Removal and Installation.
NO >>GO TO 5.
-
-
CHECK LIN COMMUNICATION SIGNAL CIRCUIT FOR OPEN
-
-
Ignition switch OFF.
-
Disconnect A/C switch assembly connector and A/C auto amp. connector.
-
Check continuity between A/C switch assembly harness connector and A/C auto amp. harness connector.
A/C switch assembly
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M59
8
M34
68
Yes
-
Is the inspection result normal?
YES >>GO TO 6.
NO >>Repair harness or connector.
-
-
CHECK LIN COMMUNICATION SIGNAL CIRCUIT FOR SHORT
-
-
Check continuity between A/C switch assembly harness connector and ground.
A/C switch assembly
—
Continuity
Connector
Terminal
M59
8
Ground
No
-
Check voltage between A/C switch assembly harness connector and ground.
+
-
Voltage
(Approx.)
A/C switch assembly
Connector
Terminal
M59
8
Ground
0 V
-
Is the inspection result normal?
YES >>Replace A/C auto amp. Refer to Removal and Installation.
NO >>Repair harness or connector.
-
Other materials:
Frequently Cannot Detect the Vehicle Ahead / Detection Zone Is Short
Diagnosis Procedure
Diagnosis Procedure
Symptom check: Detection function may become unstable under the
following conditions:
When the Nissan Sentra vehicle is driving on a curve such as an S-curve
where the curvature changes.
When the vehicle is drivin ...
Periodic Maintenance
Engine Oil
Inspection
Inspection
ENGINE OIL LEVEL
Note:
Before starting engine, put Nissan Sentra vehicle horizontally
and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
Pull out
oil level gauge and wipe it clean.
...
Power Supply, Ground & Circuit Elements. Preparation. Preparation
Preparation
Special Service Tool
Special Service Tool
Tool number
(TechMate No.)
Tool name
Description
165-GR8-1200KIT ...