S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: B24a4-11 Intake Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B24A4-11

INTAKE SENSOR

(Intake sensor)

Diagnosis condition

Ignition switch ON

Signal (Terminal)

Intake sensor signal

Threshold

The intake sensor recognition temperature is too high [more than 212°F (100°C)]

Diagnosis delay time

2 seconds or more

POSSIBLE CAUSE

  • Intake sensor

  • A/C amp.

  • Harness or connectors (The sensor circuit is shorted to ground)

FAIL-SAFE

—

Confirmation Procedure

Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Ignition switch ON.

      2. Select “Self Diagnostic Result” mode of “HVAC”.

      3. Check DTC.

    Is DTC detected?

    YES >>

    Refer to DTC Diagnosis Procedure.

    NO >>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO >>

    Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK INTAKE SENSOR SIGNAL

      1. Ignition switch ON.

      2. Check voltage between A/C amp. harness connector.

        A/C amp.

        Voltage

        (Approx.)

        Connector

        Terminals

        +

        -

        M81

        23

        26

    Is the inspection result normal?

    YES >>

    Replace A/C amp. Refer to Removal and Installation.

    NO >>

    GO TO 2.

  2. CHECK INTAKE SENSOR POWER SUPPLY

      1. Ignition switch OFF.

      2. Disconnect intake sensor connector.

      3. Ignition switch ON.

      4. Check voltage between intake sensor harness connector and ground.

        +

        -

        Voltage

        (Approx.)

        Intake sensor

        Connector

        Terminal

        M169

        1

        Ground

        5 V

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 4.

  3. CHECK INTAKE SENSOR

    1. Check intake sensor. Refer to Component Inspection.

    Is the inspection result normal?

    YES >>

    Replace A/C amp. Refer to Removal and Installation.

    NO >>

    Replace intake sensor. Refer to Removal and Installation.

  4. CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR SHORT

      1. Ignition switch OFF.

      2. Disconnect A/C amp. connector.

      3. Check continuity between intake sensor harness connector and ground.

        Intake sensor

        —

        Continuity

        Connector

        Terminal

        M169

        1

        Ground

        No

    Is the inspection result normal?

    YES >>

    Replace A/C amp. Refer to Removal and Installation.

    NO >>

    Repair harness or connector.

    B20c8-14 Compressor (ecv)
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B20C8-14 Compressor (ECV) [Compressor (elect...
    B24a4-15 Intake Sensor
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A4-15 INTAKE SENSOR (Intake sensor) Diagn...

    Other materials:

    Periodic Maintenance
    Idle Speed Idle Speed : Periodic Maintenance IDLE SPEED : Periodic Maintenance With CONSULT Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT. Without CONSULT Attach induction type (current detection type) rev counter (A) to loop wire as sho ...

    Component Parts
    Meter System Component Parts Location Component Parts Location MODELS WITH CVT A. View of engine assembly removed ...

    Basic Inspection
    Camshaft Valve Clearance Inspection and Adjustment Inspection and Adjustment INSPECTION Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if there is unusual engine conditions regarding valve clearance. Remove r ...