Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: B20c8-14 Compressor (ecv)

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20C8-14

Compressor (ECV)

[Compressor (electrical control valve)]

[CIRC SHORT TO GRND OR OPEN]

Diagnosis condition

When A/C switch is ON

Signal (Terminal)

ECV control signal

Threshold

ECV control signal circuit has a shorted to ground or open

Diagnosis delay time

1 second or more

POSSIBLE CAUSE

FAIL-SAFE

Inhibit A/C compressor (ECV) operation

Confirmation Procedure

Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Start the engine.

      2. Turn A/C switch ON.

      3. Select “Self Diagnostic Result” mode of “IPDM E/R”.

    Is DTC detected?

    YES>>

    Refer to DTC Diagnosis Procedure.

    NO>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO>>

    Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure
  1. CHECK FUSE

      1. Ignition switch OFF.

      2. Check that the following fuse is not blown (open):

        Component

        Location

        Fuse No.

        Capacity

        A/C compressor

        IPDM E/R

        89

        10 A

    Is the fuse blown (open)?

    YES >>

    Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

    NO >>

    GO TO 2.

  2. CHECK ECV POWER SUPPLY CIRCUIT

      1. Disconnect A/C compressor connector.

      2. Ignition switch ON.

      3. Check voltage between A/C compressor harness connector and ground.

        +

        Voltage

        (Approx.)

        A/C compressor

        Connector

        Terminal

        F10

        4

        Ground

        Battery voltage

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    GO TO 3.

  3. CHECK ECV POWER SUPPLY CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect IPDM E/R connector.

      3. Check continuity between A/C compressor harness connector and IPDM E/R harness connector.

        A/C compressor

        IPDM E/R

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        F10

        4

        F96

        71

        Yes

    Is the inspection result normal?

    YES >>

    Replace IPDM E/R. Refer to Removal and Installation.

    NO >>

    Repair harness or connector.

  4. CHECK ECV CONTROL SIGNAL CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect IPDM E/R connector.

      3. Check continuity between A/C compressor harness connector and IPDM E/R harness connector.

        A/C compressor

        IPDM E/R

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        F10

        3

        F98

        98

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 5.

    NO >>

    Repair harness or connector.

  5. CHECK ECV CONTROL SIGNAL CIRCUIT FOR SHORT

    1. Check continuity between A/C compressor harness connector and ground.

      A/C compressor

      Continuity

      Connector

      Terminal

      F10

      3

      Ground

      No

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair harness or connector.

  6. CHECK ECV

    1. Check ECV. Refer to Component Inspection.

    Is the inspection result normal?

    YES >>

    Replace IPDM E/R. Refer to Removal and Installation.

    NO >>

    Replace A/C compressor. Refer to Removal and Installation.

B20c7-15 A/c Clutch
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms ...

B24a4-11 Intake Sensor
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Tro ...

Other materials:

Side Oil Seal
Removal and Installation Removal and Installation REMOVAL Remove front drive shafts. Refer to Removal and Installation (LH)and Removal and Installation (RH). Remove differential side oil seals (1) from clutch housing and transaxle case using a suitable tool. CAUTION: ...

Regulatory information
FCC Regulatory Information CAUTION: To maintain full compliance with FCC RF exposure guidelines, only the supplied antenna must be used. The use of unauthorized antennas, modifications, or attachments could damage the transmitter and may result in non-compliance with FCC regulations app ...

How to Check Terminal
CONNECTOR AND TERMINAL PIN KIT Use the connector and terminal pin kits listed below when replacing connectors or terminals. The connector and terminal pin kits contain some of the most commonly used NISSAN/INFINITI connectors and terminals. For detailed connector and terminal pin repla ...

© 2014-2026 Copyright www.nisentra.com