Nissan Sentra B18 (2020-2025) Service Manual: B203f-14 Outside Antenna
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC No. |
CONSULT screen items (Trouble diagnosis content) |
DTC detecting condition |
|
|---|---|---|---|
|
B203F–14 |
Outside antenna (Outside antenna) |
Diagnosis condition |
Work support “INSIDE/OUTSIDE ANT DIAGNOSIS”: activated |
|
Signal (terminal) |
Outside key antenna (rear door RH) signal (Intelligent Key unit connector terminal: 31, 32) |
||
|
Threshold |
Outside key antenna (rear door RH) circuit is shorted to ground |
||
|
Diagnosis delay time |
1 second or less |
||
POSSIBLE CAUSE
-
Intelligent Key unit
-
Outside key antenna (rear door RH)
-
Harness or connector [outside key antenna (rear door RH) circuit is open or shorted]
FAIL-SAFE
–
Confirmation Procedure
Confirmation Procedure
-
PERFORM DTC CONFIRMATION PROCEDURE
-
CONSULTSelect “Self Diagnosis Result” mode of “HANDS FREE MODULE".
Is any DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair. Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
-
Dtc Diagnosis Procedure
DTC Diagnosis Procedure
-
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
-
-
Ignition switch ON.
-
Check signal between Intelligent Key unit harness connector and ground using oscilloscope.
(+)
(–)
Condition
Signal
(Reference value)
Intelligent Key unit
Connector
Terminal
M155
31
Ground
When the front door request switch RH is operated with push-button ignition switch ON
When Intelligent Key is in the antenna detection area
When Intelligent Key is not in the antenna detection area
32
When Intelligent Key is in the antenna detection area
When Intelligent Key is not in the antenna detection area
-
Is the inspection result normal?
YES >>Replace Intelligent Key unit. Refer to Removal and Installation.
NO >>GO TO 2.
-
-
CHECK OUTSIDE KEY ANTENNA CIRCUIT
-
-
Ignition switch OFF.
-
Disconnect Intelligent Key unit connector and outside key antenna (rear door RH) connector.
-
Check continuity between Intelligent Key unit harness connector and outside key antenna (rear door RH) connector.
Intelligent Key unit
Outside key antenna (rear door RH)
Continuity
Connector
Terminal
Connector
Terminal
M155
31
D308
2
Yes
32
1
-
Check continuity between Intelligent Key unit harness connector and ground.
Intelligent Key unit
—
Continuity
Connector
Terminal
M155
31
Ground
No
32
-
Is the inspection result normal?
YES >>GO TO 3.
NO >>Repair or replace harness.
-
-
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
-
-
Replace outside key antenna (rear door RH). (New antenna or other antenna)
-
Connect Intelligent Key unit connector and outside key antenna (rear door RH) connector.
-
Ignition switch ON.
-
Check signal between Intelligent Key unit harness connector and ground using oscilloscope.
(+)
(–)
Condition
Signal
(Reference value)
Intelligent Key unit
Connector
Terminal
M155
31
Ground
When the front door request switch RH is operated with push-button ignition switch ON
When Intelligent Key is in the antenna detection area
When Intelligent Key is not in the antenna detection area
32
When Intelligent Key is in the antenna detection area
When Intelligent Key is not in the antenna detection area
-
Is the inspection result normal?
YES >>Replace outside key antenna (rear door RH). Refer to Removal and Installation.
NO >>Replace Intelligent Key unit. Refer to Removal and Installation.
-
Other materials:
Engine Does Not Start When Intelligent Key Is Inside of Vehicle (one Key)
Diagnosis Procedure
Diagnosis Procedure
DESCRIPTION
Engine does not start when push-button ignition
switch is pressed. (One Intelligent Key has the symptom, other keys
operate normally.)
SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE
SYMPTOM, OTHER KEYS OPERATE NORMALLY)
...
Stop Lamp
Component Inspection
Component Inspection
CHECK STOP LAMP 1
Ignition switch OFF.
Disconnect rear combination lamp (body side) connector
and high-mounted stop lamp connector. ...
System Settings Cannot Be Turned On/off
Diagnosis Procedure
Diagnosis Procedure
CHECK SYSTEM SETTING
Turn ignition switch ON.
Check that the each system settings is
selectable on the combination meter.
Is the inspection result norma ...