Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / Secondary Pressure Solenoid Valve Circuit

Nissan Sentra B18 (2020-2025) Service Manual: Secondary Pressure Solenoid Valve Circuit

Diagnosis Procedure

Diagnosis Procedure

CHECK HARNESS CONNECTOR
1. Ignition switch OFF.
2. Check the mating condition of TCM harness connector and CVT unit harness connector.
Is the inspection result normal?
YES >>
GO TO 2.
NO >>
Repair or replace damaged parts.
CHECK CONNECTOR TERMINAL
1. Disconnect TCM harness connector and CVT unit harness connector.
2. Check the connectors of TCM and CVT unit for water intrusion, or damage or corrosion of the terminals.
Is the inspection result normal?
YES >>
GO TO 3.
NO >>
Repair or replace damaged parts.
CHECK DETECTED DTC

Are other solenoid valve malfunctions detected in addition to secondary pressure solenoid valve?
YES >>
GO TO 4.
NO >>
GO TO 7.

CHECK SOLENOID GROUND CIRCUIT - 1

Connect TCM harness connector.

Check continuity (resistance) between CVT unit harness connector terminal and ground.

CVT unit		—	Continuity (Resistance)
Connector	Terminal	—	Continuity (Resistance)
F46	19	Ground	Existed (1 Ω or less)

Is the inspection result normal?

YES >>

GO TO 6.

NO >>

GO TO 5.

CHECK SENSOR GROUND CIRCUIT - 2

Disconnect TCM harness connector.

Check continuity (resistance) between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Continuity (Resistance)
Connector	Terminal	Connector	Terminal	Continuity (Resistance)
F23	43	F46	19	Existed (1 Ω or less)

Is the inspection result normal?

YES >>

GO TO 6.

NO >>

Repair harness or connector.

CHECK TCM POWER SUPPLY AND GROUND CIRCUITS

Check TCM power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?
YES >>
INSPECTION END
NO >>
Repair or replace damaged parts.

CHECK SECONDARY PRESSURE SOLENOID VALVE CIRCUIT - 1

Check continuity (resistance) between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Continuity (Resistance)
Connector	Terminal	Connector	Terminal	Continuity (Resistance)
F23	39	F46	3	Existed (1 Ω or less)

Is the inspection result normal?

YES >>

GO TO 8.

NO >>

Repair harness or connector.

CHECK SECONDARY PRESSURE SOLENOID VALVE CIRCUIT - 2

Check continuity between TCM harness connector terminal and ground.

TCM		−	Continuity
Connector	Terminal	−	Continuity
F23	39	Ground	Not existed

Is the inspection result normal?

YES >>

GO TO 9.

NO >>

Repair harness.

CHECK SECONDARY PRESSURE SOLENOID VALVE

Check resistance between CVT unit connector terminals.

CVT unit		Test condition		Resistance
Terminal		Test condition		Resistance
3	19	CVT fluid temperature	20°C (68°F)	5.0 – 5.6 Ω
			50°C (122°F)	5.5 – 6.8 Ω
			80°C (176°F)	6.0 – 8.0 Ω

Is the inspection result normal?

YES >>

INSPECTION END

NO >>

Replace control valve due to secondary pressure solenoid valve malfunction. Refer to Removal and Installation.

 Primary Pressure Solenoid Valve Circuit

Diagnosis Procedure Diagnosis Procedure CHECK HARNESS CONNECTOR Ignition switch OFF. Check the mating condition of TCM harness connector and CVT unit harness connector. Is the i...

 Select Solenoid Valve Circuit

Diagnosis Procedure Diagnosis Procedure CHECK HARNESS CONNECTOR Ignition switch OFF. Check the mating condition of TCM harness connector and CVT unit harness connector. Is the i...

Other materials:

Sun visors
1. To reduce glare from the front, pull down the main sun visor 1. 2. To block glare from the side window, remove the main sun visor from the center mount and swing it toward the side 2. 3. To extend coverage, slide the sun visor extension in or out as needed 3. CAUTION Always return th ...

Sonar System. Removal and Installation. Sonar Control Unit. Removal and Installation
Sonar Control Unit. Removal and Installation Removal and Installation Removal and Installation REMOVAL CAUTION: When replacing the sonar control unit, perform "ADDITIONAL SERVICE WHEN REPLACING SONAR CONTROL UNIT". Refer to Work Procedure. Partially remove the trunk s ...

Basic Inspection
Diagnosis and Repair Workflow Work Flow Work Flow OVERALL SEQUENCE Reference 1··· Refer to CONSULT Function. Reference 2··· Refer to DTC Index. Reference 3··· Refer to Symptom Table. DETAILED FLOW INTERVIEW AND S ...