Nissan Sentra B18 (2020-2025) Service Manual: P27eb-00 Transmission Range Control a Position Sensor/switch

Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / P27eb-00 Transmission Range Control a Position Sensor/switch

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC		CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P27EB	00	T/M RANGE CTRL A POSI SEN/SW (Transmission Range Control "A" Position Sensor/Switch Circuit/Open)	1	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 1 signal
				Threshold	Transmission range switch 1 status is open circuit
				Diagnosis delay time	0.3 seconds
			2	Diagnosis condition	Power supply voltage ≥ 10 V
				Signal	Transmission range switch 1 signal
				Threshold	Transmission range switch 1 status is intermediate voltage
				Diagnosis delay time	0.3 seconds

POSSIBLE CAUSE

Harness or connector
Transmission range switch
TCM

FAIL-SAFE

Shift position indicator on combination meter is not displayed
Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V.

>>
GO TO 2.
CHECK DTC DETECTION
1. Ignition switch ON.
2. Shift the selector lever to "R" position and wait for 5 seconds or more.
3. Shift the selector lever to "N" position and wait for 5 seconds or more.
4. Shift the selector lever to "D" position and wait for 5 seconds or more.
5. Shift the selector lever to "L" position and wait for 5 seconds or more.
6. Shift the selector lever to "P" position and wait for 5 seconds or more.
7. Check the DTC
Is "P27EB-00" detected?
YES >>
Proceed to Diagnosis Procedure.
NO-1>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>
Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

CHECK TRANSMISSION RANGE SWITCH 1 CIRCUIT

Check transmission range switch 1 circuit. Refer to Diagnosis Procedure.

>>
GO TO 2.
CHECK DTC DETECTION

Perform DTC confirmation procedure. Refer to DTC Description.

Is "P27EB-00" detected again?
YES >>
Replace TCM. Refer to Removal and Installation.
NO >>
INSPECTION END

P27b5-00 Control Module

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms ( ...

P27ec-00 Transmission Range Control a Position Sensor/switch

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms ...

Other materials:

Voice commands
Voice commands can be used to operate the Bluetooth® Hands-Free Phone System. Press the button and say “Phone” to bring up the phone command menu. The available options are: Call Phonebook Recent Calls Send Text Read Text Select Phone “Call” For more information on ...

P0090 Fuel Rail Pressure Control System
Dtc Description DTC Description DTC DETECTION LOGIC Note: DTC P0090 may be displayed when running out of gas. DTC CONSULT screen terms (Trouble diagnosis content) ...

P0713 Transmission fluid temperature sensor A
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0713 FLUID TEMP SENSOR A (Transmission Fluid Temperature Sensor A Circuit High) The CVT fluid temperature identified by the TCM is ...