Nissan Sentra B18 (2020-2025) Service Manual: P2619 Crankshaft Position Sensor

Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P2619 Crankshaft Position Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P2619	Crankshaft position signal (Crankshaft position signal output circuit high)	Diagnosis condition	Engine running at idle
		Signal (terminal)	Crankshaft position sensor signal for electric intake valve timing control
		Threshold	The crankshaft position sensor signal edge count is more than 18 counts per one camshaft rotation
		Diagnosis delay time	1 second

POSSIBLE CAUSE

Harness or connectors (Crankshaft position sensor signal circuit for electric intake valve timing control is open or shorted.)

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).
	Idle speed control	Stops feedback control of idle speed and controls with specified speed.
	Recovery speed control at decelerating	Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
	Idle neutral control	Stops idle neutral control.
Others		ECM stops the electric valve timing control. (The camshaft returns to the position of most retard angle.)

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2619 is displayed with DTC P0335 or P0643, first perform the confirmation procedure (trouble diagnosis) for DTC P0335 or P0643.

Is DTC P0335 or P0643 detected?
YES >>
Perform diagnosis of applicable.
- DTC P0335: Refer to DTC Description.
- DTC P0643: Refer to DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait at least 5 seconds.
2. Check 1st trip DTC.
Is DTC P2619 detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2619 is displayed with DTC P0335 or P0643, first perform the confirmation procedure (trouble diagnosis) for DTC P0335 or P0643.

Is DTC P0335 or P0643 detected?
YES >>
Perform diagnosis of applicable.
- DTC P0335: DTC Description.
- DTC P0643: DTC Description.
NO >>
GO TO 2.

CHECK CRANKSHAFT POSITION (CKP) SENSOR SIGNAL CIRCUIT FOR ELECTRIC INTAKE VALVE TIMING CONTROL

Turn ignition switch OFF.
Disconnect ECM harness connector and electric intake valve timing control module harness connector.

Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.

ECM		Electric intake valve timing control module		Continuity
Connector	Terminal	Connector	Terminal	Continuity
F24	22	F80	28	Existed

Also check harness for short to power and short to ground.

Is the inspection result normal?

YES >>

INSPECTION END

NO >>

Repair or replace error-detected parts.

P2618 Crankshaft Position Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

P2a01 O2 Sensor 2 Bank 1

Dtc Description DTC Description The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of th ...

Other materials:

Description
Description Note: Trouble diagnoses indicate work procedures required to diagnose problems effectively. Observe the following instructions before diagnosing. Before performing trouble diagnoses, read the “Work Flow” in each section. After repair ...

Turn Signal Lamp Circuit
Component Function Check Component Function Check CHECK TURN SIGNAL LAMP OPERATION CONSULT Select “FLASHER” in "Active Test" mode of “BCM(FLASHER)". With operating the t ...

The oil pressure warning lamp does not turn on
Description The oil pressure warning lamp stays off when the ignition switch is turned on. Diagnosis procedure 1.Check combination meter oil pressure warning light Select METER/M&A on CONSULT. Observe oil w/l data monitor while operating the ignition switch. Is the inspection r ...