S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P1ae0-61 Range Misdisplay

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P1AE0

61

Range misdisplay

(Range Misdisplay)

Diagnosis condition

—

Signal

—

Threshold

Display range signal and redundant display range signal do not match

Diagnosis delay time

Within 1 second

POSSIBLE CAUSE

TCM

FAIL-SAFE

Shift position indicator on combination meter is not displayed

DTC CONFIRMATION PROCEDURE

  1. PREPARATION BEFORE WORK

    If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is more than 10 V.

    >>

    GO TO 2.

  2. CHECK DTC DETECTION

    With CONSULT

    1. Ignition switch ON and wait for 10 seconds.

    2. Shift the selector lever to "R" position and wait for 5 seconds or more.

    3. Shift the selector lever to "N" position and wait for 5 seconds or more.

    4. Shift the selector lever to "D" position and wait for 5 seconds or more.

    5. Shift the selector lever to "L" position and wait for 5 seconds or more.

    6. Shift the selector lever to "P" position and wait for 5 seconds or more.

    7. Check the DTC.

    Is "P1AE0-61" detected?

    YES >>

    Go to DTC Diagnosis Procedure.

    NO >>

    INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. REPLACE TCM

    Replace TCM. Refer to Removal and Installation.

    >>

    WORK END

    P188e-00 Electric Oil Pump
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P188E 00 ELECTRIC OIL PUMP (Electric Oil Pump) D...
    P271e-00 Wheel Torque Calculation Signal
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P271E 00 Wheel torque calculation signal 1 Diagn...

    Other materials:

    Removal and Installation (lh)
    Removal and Installation (LH) Note: When removing components such as hoses, tubes, lines, etc., cap or plug openings to prevent fluid from spilling. REMOVAL For M/T models, drain the M/T oil. Refer to Draining. Remove disc brake rotor. Refer to Removal and Installation. ...

    P059f Active Grille Shutter
    Dtc Description DTC Description DTC DETECTION LOGIC Active grille shutter normally stops within zone which is defined by zone (90°±20°). If the active grille shutter stops within zone stuck error is detected, and if the active grille shutter stops at position beyond zon ...

    P1217 Engine Over Temperature
    Dtc Description DTC Description ECM controls cooling fan to the maximum speed when receives the signal abnormality of each sensor, CAN and IPDM E/R, and severed wire short circuit abnormality. If the cooling fan or another component in the cooling system malfunctions, engine coola ...