S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P188e-00 Electric Oil Pump

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P188E

00

ELECTRIC OIL PUMP

(Electric Oil Pump)

Diagnosis condition

Diagnosis is permitted when all of the following conditions are satisfied:

a) Ignition voltage ≥ 9.01 V

b) Battery voltage ≥ 9.01 V

c) After ignition on, 1 sec has elapsed.

Signal

—

Threshold

DTC is detected when one of the following conditions "a" to "g" are satisfied:

a) ASIC diagnosis error

b) Microcomputer/Sensor voltage error

c) Overtemperature error

d) Inverter error

e) Angle sensor error

f) Motor error

g) Communication error

Diagnosis delay time

1.9 second

POSSIBLE CAUSE

  • Harness or connector

  • Battery

  • Electric oil pump

FAIL-SAFE

Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

  1. PREPARATION BEFORE WORK

    If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is more than 10 V.

    >>

    GO TO 2.

  2. CHECK DTC DETECTION

    1. Start the engine.

    2. Check the DTC.

    Is "P188E-00" detected?

    YES >>

    Proceed to DTC Diagnosis Procedure.

    NO-1>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2>>

    Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK ELECTRIC OIL PUMP POWER SUPPLY

    1. Ignition switch OFF.

    2. Disconnect CVT unit harness connector.

    3. Ignition switch ON.

    4. Check voltage between CVT unit harness connector terminal and ground.

      +

      -

      Voltage

      CVT unit

      Connector

      Terminal

      F56

      24

      Ground

      10 - 16 V

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 2.

  2. CHECK ELECTRIC OIL PUMP POWER SUPPLY CIRCUIT - 1

    Check the following items:

    • Open or short circuit of harness between battery positive terminal and CVT unit harness connector terminal 24.

    • 60A fusible link (No. L)

    Is the inspection result normal?

    YES >>

    INSPECTION END

    NO >>

    Repair harness, connector, or fusible link

  3. CHECK ELECTRIC OIL PUMP GROUND CIRCUIT - 1

    1. Ignition switch OFF.

    2. Check continuity between CVT unit harness connector terminal and ground.

      CVT unit

      -

      Continuity

      Connector

      Terminal

      F56

      23

      Ground

      Existed

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair harness or connector.

  4. CHECK ELECTRIC OIL PUMP CAN CIRCUIT - 1

    1. Disconnect TCM harness connector.

    2. Check resistance between TCM harness connector terminals and CVT unit harness connector terminals.

    TCM

    CVT unit

    Resistance

    Connector

    Terminal

    Connector

    Terminal

    F23

    31

    F46

    11

    1 Ω or less

    32

    10

    Is the inspection result normal?

    YES >>

    GO TO 5.

    NO >>

    Repair harness or connector.

  5. CHECK ELECTRIC OIL PUMP GROUND CIRCUIT - 2

    1. Remove control valve cover. Refer to Removal and Installation.

      CAUTION:

      Never disconnect harness connector F102 inside the CVT unit. Refer to Wiring Diagram.

    2. Check continuity between CVT unit connector terminal and electric oil pump harness terminal.

      CVT unit

      Electric oil pump

      Continuity

      Terminal

      Connector

      Terminal

      23

      F108

      5

      Existed

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair harness or connector.

  6. CHECK ELECTRIC OIL PUMP POWER SUPPLY CIRCUIT - 2

    Check continuity between CVT unit connector terminal and electric oil pump harness terminal.

    CVT unit

    Electric oil pump

    Continuity

    Terminal

    Connector

    Terminal

    24

    F107

    4

    Existed

    Is the check result normal?

    YES >>

    GO TO 7.

    NO >>

    Repair harness or connector.

  7. CHECK ELECTRIC OIL PUMP CAN CIRCUIT - 2

    1. Disconnect electric oil pump harness connector.

    2. Check resistance between CVT unit connector terminals and electric oil pump harness connector terminals.

      CVT unit

      Electric oil pump

      Resistance

      Terminal

      Connector

      Terminal

      10

      F106

      2

      1 Ω or less

      11

      3

    Is the inspection result normal?

    YES >>

    Replace electric oil pump. Refer to Removal and Installation.

    NO >>

    Replace control valve due to harness connector malfunction. Refer to Removal and Installation.

    P187e-09 T/m System Malfunction
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P187E 09 T/M SYSTEM MALFUNCTION (T/M System Malf...
    P1ae0-61 Range Misdisplay
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1AE0 61 Range misdisplay (Range Misdisplay) Dia...

    Other materials:

    Hood Lock
    Exploded View Exploded View 1. Hood lock 2. Hood lock release cable 3. ...

    P0335 Ckp Sensor
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...

    Charging System. System Description
    Component Parts Charging System Component Parts Location Component Parts Location No. Component Function 1. ...