Nissan Sentra B18 (2020-2025) Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f15a / Dtc/circuit Diagnosis / P0961-00 Pressure Control Solenoid a

Nissan Sentra B18 (2020-2025) Service Manual: P0961-00 Pressure Control Solenoid a

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC		CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0961	00	PC SOLENOID A (Pressure Control Solenoid "A" Control Circuit Range/Performance)	Diagnosis condition	Diagnosis is permitted when all of the following conditions are satisfied: a) Ignition voltage ≥ 9.01 V b) Battery voltage ≥ 9.01 V c) Engine speed > 600 rpm d) Primary pulley speed > 450 rpm e) "Primary pulley speed ≥ 267 rpm" and "Secondary pulley speed ≥ 270 rpm" are experienced at least once. f) "0.5 sec passed after ignition ON" and "Secondary pulley speed > 43 rpm + 1/10" are experienced at least once. g) Acceleration and deceleration ≥ -0.05 G h) Idling is not being judged. i) The following "i-1" and "i-2" is satisfied. i-1) ABS Nissan Sentra vehicle speed ≤ 3 km/h (2 MPH) i-2) Secondary pulley speed > 150 rpm
			Signal	—
			Threshold	DTC is detected when one of the following conditions "a" and "B" are satisfied: a) Primary pulley speed / Secondary pulley speed > 3.419 : Continue for 0.2 sec b) Primary pulley speed / Secondary pulley speed > 4.106 : Continue for 0.1 sec [Interval (diagnosis masking time) after first judgement must be 1 sec or more.]
			Diagnosis delay time	—

POSSIBLE CAUSE

Harness or connector
Line pressure solenoid valve
Control valve
Secondary speed sensor
TCM

FAIL-SAFE

When a malfunction occurs on the low oil pressure side

Start is slow
Acceleration is slow
Lock-up is not performed
Nissan Sentra Vehicle speed is not increased
Stop/start system prohibited

When a malfunction occurs on the high oil pressure side

Start is slow
Acceleration is slow
Lock-up is not performed
Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V.

>>
GO TO 2.

CHECK DTC DETECTION

Start the engine.

Drive the Nissan Sentra vehicle and maintain the following conditions for 10 seconds or more.

Shift position	: "D" position
Accelerator pedal opening	: 0.5/8 or more
Nissan Sentra Vehicle speed	: 40 km/h (25 MPH) or more

CAUTION:

Be careful of the driving speed.

Stop the Nissan Sentra vehicle.
Check the DTC.

Is "P0961-00" detected?

YES >>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

INSPECT CVT STEEL BELT

Inspect the CVT steel belt. Refer to Component Inspection.

Is CVT steel belt OK?
YES >>
GO TO 2.
NO >>
GO TO 5.
CHECK SECONDARY SPEED SENSOR - 1

Check secondary speed sensor. Refer to Diagnosis Procedure.

Is the inspection result normal?
YES >>
GO TO 3.
NO>>
Repair or Replace damaged part.

CHECK LINE PRESSURE SOLENOID VALVE CIRCUIT - 1

Disconnect TCM harness connector.
Disconnect CVT unit harness connector.

Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Resistance
Connector	Terminal	Connector	Terminal	Resistance
F23	30	F46	1	1 Ω or less

Is the inspection result normal?

YES >>

GO TO 4.

NO >>

Repair harness or connector.

REPLACE CONTROL VALVE

Replace control valve. Refer to Removal and Installation.

>>
GO TO 8.
CHECK SECONDARY SPEED SENSOR - 2

Check secondary speed sensor. Refer to Diagnosis Procedure.

Is the inspection result normal?
YES >>
GO TO 6.
NO>>
Repair or Replace damaged part.

CHECK LINE PRESSURE SOLENOID VALVE CIRCUIT - 2

Disconnect TCM harness connector.
Disconnect CVT unit harness connector.

Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

TCM		CVT unit		Resistance
Connector	Terminal	Connector	Terminal	Resistance
F23	30	F46	1	1 Ω or less

Is the inspection result normal?

YES >>

GO TO 7.

NO >>

Repair harness or connector.
GO TO 7.

REPLACE BELT AND PULLEYS

Replace belt and pulleys. Refer to Disassembly and Assembly.

>>
GO TO 8.
CHECK DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?
YES >>
Replace TCM. Refer to Removal and Installation.
NO >>
INSPECTION END

 P0960-00 Pressure Control Solenoid a

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0960 00 PC SOLENOID A (Pressure Control Solenoi...

 P1588-00 Decel G Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1588 00 G SENSOR (Decel G Sensor Performance) D...

Other materials:

Rear-facing child restraint installation using LATCH
Do not use the LATCH lower anchors if the combined weight of the child and the child restraint exceeds 65 lbs (29.5 kg). If the combined weight is greater than 65 lbs (29.5 kg), install the child restraint using the vehicle’s seat belt instead of the lower anchors. Always follow the child re ...

P2812-00 Pressure Control Solenoid G
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection conditi ...

iPod* player operation
Type-A. Connecting iPod WARNING Do not connect, disconnect, or operate the USB device while driving. Doing so may distract the driver. If distracted, you could lose control of your Nissan Sentra, which could result in an accident causing serious injury. CAUTION Do not force the ...