Nissan Sentra B18 (2020-2025) Service Manual: Inspection
PRELIMINARY INSPECTION
Warning:
Always adjust the wheel alignment with the Nissan Sentra vehicle on a flat surface.
Note:
If the wheel alignment is out of specification, inspect and replace any damaged or worn rear suspension parts before making any adjustments.
Check and adjust the wheel alignment with the Nissan Sentra vehicle under unladen conditions. “Unladen conditions” means that the fuel, engine coolant, and lubricants are full; the spare tire, jack, hand tools and mats are in designated positions.
Check the tires for incorrect air pressure and excessive wear.
Check the wheels for run out and damage. Refer to Inspection.
Check the wheel bearing axial end play. Refer to Inspection.
Check the shock absorbers for leaks or damage.
Check each mounting point of the suspension components for any excessive looseness or damage.
Check each link, arm, and the suspension member for any damage.
Check the Nissan Sentra vehicle height. Refer to Wheelarch Height (Unladen) .
GENERAL INFORMATION AND RECOMMENDATIONS
A Four-Wheel Thrust Alignment should be performed.
-
This type of alignment is recommended for any NISSAN Nissan Sentra vehicle.
-
The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel is centered.
-
The alignment machine itself should be capable of accepting any NISSAN Nissan Sentra vehicle.
-
The alignment machine should be checked to ensure that it is level.
Make sure the alignment machine is properly calibrated.
-
Your alignment machine should be regularly calibrated in order to give correct information.
-
Check with the manufacturer of your specific alignment machine for their recommended Service/Calibration Schedule.
THE ALIGNMENT PROCESS
IMPORTANT: Use only the alignment specifications listed in this Service Manual. Refer to Wheel Alignment (Unladen).
-
When displaying the alignment settings, many alignment machines use “indicators”: (Green/red, plus or minus, Go/No Go). Do NOT use these indicators.
-
The alignment specifications programmed into your alignment machine that operate these indicators may not be correct.
-
This may result in an ERROR.
-
-
Most camera-type alignment machines are equipped with both "Rolling Compensation" method and optional "Jacking Compensation" method to "compensate" the alignment targets or head units.
"Rolling Compensation" is the preferred method.
-
If using the "Rolling Compensation" method, after installing the alignment targets or head units, push or pull on the rear wheel to move the Nissan Sentra vehicle. Do not push or pull the vehicle body.
-
If using the "Jacking Compensation" method, after installing the alignment targets or head units, raise the Nissan Sentra vehicle and rotate the wheels 1/2 turn both ways.
-
Do not use the "Rolling Compensation" method if you are using sensor-type alignment equipment.
-
Follow all instructions for the alignment machine you're using for more information.
CAMBER, CASTER AND KINGPIN INCLINATION ANGLES INSPECTION
-
Camber, caster, kingpin inclination angles cannot be adjusted.
-
Before inspection, set the front wheels onto a turning radius gauge. Set the rear wheels onto a pad that has the same height so the Nissan Sentra vehicle will remain horizontal.
TOTAL TOE-IN INSPECTION
Measure the total toe-in using the following procedure.
Warning:
-
Always perform the following procedure on a flat surface.
-
Make sure that no person is in front of Nissan Sentra vehicle before pushing it.
Bounce the front of vehicle up and down to stabilize the Nissan Sentra vehicle height (posture).
Push on the rear wheel to move the vehicle straight ahead about 5 m (16 ft).
Put a mark
on base line of the tread (rear side) of both tires at the same
height of hub center. These are measuring points.
Measure the
distance (A) from the rear side. 
Push on the rear wheel to move the Nissan Sentra vehicle slowly ahead and to rotate the wheels 180 degrees (1/2 turn).
CAUTION:
If the wheels have rotated more than 180 degrees (1/2 turn), try the above procedure again from the beginning. Do not push Nissan Sentra vehicle backward.
Measure the distance (B) from the front side.
Use the formula below to calculate total toe-in.
|
Total toe-in |
: A - B |
|
Total toe-in specification |
: Refer to Wheel Alignment (Unladen). |
-
If the total toe-in is outside the specification, adjust the total toe-in. Refer to Adjustment.
Wheel Alignment
...
Adjustment
Adjustment
TOTAL TOE-IN
Loosen the
steering outer socket.
Adjust the
length using the steering inner socket.
Toe-in
...
Other materials:
Headlight control switch
Type A (if so equipped)
Type B (if so equipped)
Lighting
Rotate the switch to the
position to turn on the front parking lights, tail lights, license plate lights,
and instrument panel illumination. The
indicator will illuminate in the meter.
Rotate the switch to the
...
Dlc branch line circuit
Diagnosis Procedure
1.Check connector
Turn the ignition switch off.
Disconnect the battery cable from the negative terminal
Check the terminals and connectors of the data link connector for
damage, bend and loose connection
(connector side and harness side).
Is the inspection result ...
Dtc Confirmation Procedure
DTC Confirmation Procedure
PERFORM DTC CONFIRMATION
CONSULT
Ignition switch ON.
CAUTION:
Never start the engine.
...
