Nissan Sentra B18 (2020-2025) Service Manual / Steering / Steering Control System :: Dtc/circuit Diagnosis / C1629-87 Ipdm E/r System

Nissan Sentra B18 (2020-2025) Service Manual: C1629-87 Ipdm E/r System

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
C1629-87	IPDM E/R system (Intelligent power distribution module engine room system)	Diagnosis condition	When ignition switch is ON.
		Signal (terminal)	CAN communication signal
		Threshold	When a malfunction is detected in IPDM E/R.
		Diagnosis delay time	2 seconds or more

POSSIBLE CAUSE

CAN communication line
IPDM E/R
EPS control unit

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING
1. If “Confirmation Procedure” has been previously conducted, always place the ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
DTC REPRODUCTION PROCEDURE
1. CONSULT
  1. Ignition switch ON.
  2. Select "Self Diagnostic Result" mode of “EPS/DAST 3”.
Is DTC “C1629-87” detected?
YES>>
Proceed to diagnosis procedure. Refer to DTC Diagnosis Procedure.
NO>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>
Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC RESULT
1. CONSULT
  1. Ignition switch ON.
  2. Select "Self Diagnostic Result" mode of “IPDM E/R”.
Is any DTC detected?
YES >>
Check the DTC. Refer to DTC Index.
NO >>
GO TO 2.
CHECK CONNECTOR AND TERMINAL
1. 1. Ignition switch OFF.
  2. Disconnect IPDM E/R harness connector.
  3. Disconnect EPS control unit harness connector.
  4. Check the connector for disconnection or looseness.
  5. Check the pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >>
GO TO 3.
NO >>
Repair or replace harness, connector, or terminal, securely lock the connector.
PERFORM SELF DIAGNOSTIC RESULT
1. CONSULT
  1. Connect IPDM E/R harness connector.
  2. Connect EPS control unit harness connector.
  3. Ignition switch ON.
  4. Erase "Self Diagnostic Result" mode of "EPS/DAST 3".
  5. Ignition switch OFF and wait for at least 10 seconds.
  6. Ignition switch ON.
  7. Select "Self Diagnostic Result" mode of “EPS/DAST 3”.
Is DTC “C1629-87” detected?
YES>>
EPS control unit is malfunctioning. Replace steering gear assembly. Refer to Removal and Installation.
NO>>
Inspection End.

 C1624-00 Signal Connector

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1624-00 Signal connector (Signal connector)...

 C1630-87 Can Comm Circuit

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1630-87 CAN COMM CIRCUIT (Control module co...

Other materials:

U0073-00 Can Comm Circuit
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...

C1608-54 Control Unit
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...

Intelligent Key Battery. Removal and Installation
Removal and Installation Removal and Installation Release the lock knob at the back of the Intelligent Key and remove the mechanical key. Insert remover tool (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper par ...