Dtc Description
DTC DETECTION LOGIC
|
DTC No. |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
||
|---|---|---|---|---|
|
B2E0B-01 |
SOS LED (Auto) [SOS LED (Auto)] |
1 |
Diagnosis condition |
When ignition switch is ON |
|
Signal (terminal) |
SOS switch LED (Green) signal (terminal 5) |
|||
|
Threshold |
Not connected or open circuit |
|||
|
Diagnosis delay time |
1 second or more |
|||
|
2 |
Diagnosis condition |
When ignition switch is ON |
||
|
Signal (terminal) |
SOS switch LED (Green) signal (terminal 5) |
|||
|
Threshold |
1.2 V or less |
|||
|
Diagnosis delay time |
1 second or more |
|||
|
3 |
Diagnosis condition |
When ignition switch is ON |
||
|
Signal (terminal) |
SOS switch LED (Green) signal (terminal 5) |
|||
|
Threshold |
5.8 V or more |
|||
|
Diagnosis delay time |
1 second or more |
|||
POSSIBLE CAUSE
Moonroof switch assembly (telematics switch) is not connected,
SOS switch LED (Green) signal is open
SOS switch LED (Green) signal is short to ground
SOS switch LED (Green) signal is short to battery
FAIL-SAFE
Telematics system does not operate
Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON.
Ignition switch OFF and wait at least 30 seconds.
Ignition switch ON and wait at least 30 seconds or more.
Select “Self Diagnostic Result” mode of “IVC”.
Check DTC.
Is DTC B2E0B–01 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
Dtc Diagnosis Procedure
CHECK SOS SWITCH LED (GREEN) SIGNAL
Ignition switch ON.
Check the voltage between TCU connector and ground.
|
(+) |
(-) |
Condition |
Voltage (Approx.) |
|
|---|---|---|---|---|
|
TCU |
||||
|
Connector |
Terminal |
|||
|
M160 |
5 |
Ground |
SOS switch LED (Green) not illuminated |
5 V |
|
SOS switch LED (Green) illuminated |
0 V |
|||
Is the inspection result normal?
YES >>GO TO 2.
NO >>Replace TCU. Refer to Removal and Installation.
CHECK SOS SWITCH LED (GREEN) SIGNAL CIRCUIT FOR OPEN
Ignition switch OFF.
Disconnect TCU connector and moonroof switch assembly (telematics switch) connector.
Check the continuity between TCU connector and moonroof switch assembly (telematics switch) connector.
|
TCU |
Moonroof switch assembly (telematics switch) |
Continuity |
||
|
Connector |
Terminal |
Connector |
Terminal |
|
|
M160 |
5 |
R27 |
5 |
Yes |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connector.
CHECK SOS SWITCH LED (GREEN) SIGNAL CIRCUIT FOR SHORT
Ignition switch ON.
Check the voltage between TCU connector and ground.
|
(+) |
(-) |
Voltage (Approx.) |
|
|---|---|---|---|
|
TCU |
|||
|
Connector |
Terminal |
||
|
M160 |
5 |
Ground |
0 V |
Is the inspection result normal?
YES >>GO TO 4.
NO >>Repair or replace harness or connector.
CHECK SOS SWITCH LED (GREEN) SIGNAL CIRCUIT FOR SHORT
Ignition switch OFF.
Check the continuity between TCU connector and ground.
|
TCU |
— |
Continuity |
|
|---|---|---|---|
|
Connector |
Terminal |
||
|
M160 |
5 |
Ground |
No |
Is the inspection result normal?
YES >>Replace moonroof switch assembly (telematics switch). Refer to Removal and Installation.
NO >>Repair or replace harness or connector.
B2e08 Microphone
B2e0f Gnss Communications FailureCommercial Service Tools
Commercial Service Tools
Tool name
Description
Power tool
Loosening nuts, screws and
bolts
...
Intake/exhaust Camshaft Position Sensor
Component Inspection
Component Inspection
CHECK CAMSHAFT POSITION SENSOR
(PHASE)-1
Turn ignition switch OFF.
Loosen the fixing bolt of the
sensor.
Disconnect camshaft position senso ...
Fuel recommendation
Use unleaded regular gasoline with an octane
rating of at least 87 AKI (Anti-Knock Index) number
(Research octane number 91).
CAUTION
Only vehicles with the E-85 filler door
label can operate on E-85. Fuel system
or other damage can occur if E-85 is
used in vehicles that are not designe ...