S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: B24a4-15 Intake Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B24A4-15

INTAKE SENSOR

(Intake sensor)

Diagnosis condition

Ignition switch ON

Signal (Terminal)

Intake sensor signal

Threshold

The intake sensor recognition temperature is too low [less than -44°F (-42°C)]

Diagnosis delay time

2 seconds or more

POSSIBLE CAUSE

  • Intake sensor

  • A/C auto amp.

  • Harness or connectors (The sensor circuit is open or shorted to battery)

FAIL-SAFE

—

Confirmation Procedure

Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Ignition switch ON.

      2. Select “Self Diagnostic Result” mode of “HVAC”.

      3. Check DTC.

    Is DTC detected?

    YES>>

    Refer to DTC Diagnosis Procedure.

    NO>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO>>

    Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK INTAKE SENSOR SIGNAL

      1. Ignition switch ON.

      2. Check voltage between A/C auto amp. harness connector.

        A/C auto amp.

        Voltage

        (Approx.)

        Connector

        Terminals

        +

        -

        M33

        23

        26

    Is the inspection result normal?

    YES >>

    Replace A/C auto amp. Refer to Removal and Installation.

    NO >>

    GO TO 2.

  2. CHECK INTAKE SENSOR POWER SUPPLY

      1. Ignition switch OFF.

      2. Disconnect intake sensor connector.

      3. Ignition switch ON.

      4. Check voltage between intake sensor harness connector and ground.

        +

        -

        Voltage

        (Approx.)

        Intake sensor

        Connector

        Terminal

        M169

        1

        Ground

        5 V

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 5.

  3. CHECK INTAKE SENSOR GROUND CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect A/C auto amp. connector.

      3. Check continuity between intake sensor harness connector and A/C auto amp. harness connector.

        Intake sensor

        A/C auto amp.

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M169

        2

        M33

        26

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair harness or connector.

  4. CHECK INTAKE SENSOR

    1. Check intake sensor. Refer to Diagnosis Procedure.

    Is the inspection result normal?

    YES >>

    Replace A/C auto amp. Refer to Removal and Installation.

    NO >>

    Replace intake sensor. Refer to Removal and Installation.

  5. CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect A/C auto amp. connector.

      3. Check continuity between intake sensor harness connector and A/C auto amp. harness connector.

        Intake sensor

        A/C auto amp.

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M169

        1

        M33

        23

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair harness or connector.

  6. CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR SHORT

    1. Check voltage between intake sensor harness connector and ground.

      +

      -

      Voltage

      (Approx.)

      Intake sensor

      Connector

      Terminal

      M169

      1

      Ground

      0 V

    Is the inspection result normal?

    YES >>

    Replace A/C auto amp. Refer to Removal and Installation.

    NO >>

    Repair harness or connector.

    B24a4-11 Intake Sensor
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A4-11 INTAKE SENSOR (Intake sensor) Diagn...
    B24b4-02 A/c Control
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24B4-02 A/C CONTROL (Air conditioning contr...

    Other materials:

    Torque Converter and Converter Housing Oil Seal
    Exploded View Exploded View Torque converter Converter housing oil seal ...

    Headlamp Warning Circuit
    Component Function Check Component Function Check CHECK HEADLAMP WARNING OPERATION Ignition switch ON. Check that headlamp warning on combination meter is not displayed ...

    Roof. Basic Inspection
    Diagnosis and Repair Work Flow. Work Flow Work Flow Work Flow OVERALL SEQUENCE DETAILED FLOW INTERVIEW CUSTOMER Interview the customer to obtain as much information as possible about the conditions and environment under which the malfuncti ...