Nissan Sentra Owners Manual: Using the system

The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth® Phone System.

If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.

Initialization

When the ignition switch is placed in the ON position, NISSAN Voice Recognition is initialized, which takes a few seconds. If the
button is pressed before the initialization completes, the system will announce “Hands-free phone system not ready” and will not react to voice commands.

Operating tips

To get the best performance out of the NISSAN Voice Recognition system, observe the following:

• Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly.
• Wait until the tone sounds before speaking a command. Otherwise, the command will not be received properly.
• Start speaking a command within 5 seconds after the tone sounds.
• Speak in a natural voice without pausing between words.

Giving voice commands

To operate NISSAN Voice Recognition, press and release the button located on the
steering wheel. After the tone sounds, speak a command.

The command given is picked up by the microphone, and voice feedback is given when the command is accepted.

• If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them.
• If a command is not recognized, the system announces, “Command not recognized.

  Please try again.”Make sure the command is said exactly as prompted by the system and repeat the command in a clear voice.

• If you want to go back to the previous command, you can say “Go back” or “Correction” any time the system is waiting for a response.
• You can cancel a command when the system is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. You can also press and hold the button
  on the steering wheel for 5 seconds at any time to end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.
• If you want to adjust the volume of the voice feedback, press the volume control switches (+ or -) on the steering wheel while being provided with feedback. You can also use the radio volume control knob.

How to say numbers

NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following rules and examples.

• Either “zero” or “oh” can be used for “0”.

Example: 1-800-662-6200

• “One eight oh oh six six two six two oh oh”, or
• “One eight zero zero six six two six two oh oh”

• Words can be used for the first 4 digits places only.

Example: 1-800-662-6200

• “One eight hundred six six two six two oh oh”,
• NOT “One eight hundred six six two sixty two hundred,” and
• NOT “One eight oh oh six six two sixty two hundred”

• Numbers can be spoken in small groups.

  The system will prompt you to continue entering digits, if desired.

Example: 1-800-662-6200

• “One eight zero zero”

The system repeats the numbers and prompts you to enter more.

• “Six six two”

The system repeats the numbers and prompts you to enter more.

• “Six two zero zero”

• Say “pound” for “#”. Say “star” for “*” (available when using the “Special Number” command and the “Send” command during a call).

  See “List of voice commands” and “Special number” in this section for more information.

  Example: 1-555-1212 *123

• “One five five five one two one two star one two three”

• Say “plus” for “+” (available only when using the “Special Number” command).
• Say “pause” for a 2-second pause (available only when storing a phonebook number).

NOTE:

For best results, say phone numbers as single digits.

The voice command “Help” is available at any time. Please use the “Help” command to get information on how to use the system.

Voice Prompt Interrupt

In most cases you can interrupt the voice feedback to speak the next command by pressing the button on the steering wheel.
After interrupting the system, wait for a beep before speaking your command.

One Shot Call

To use the system faster, you may speak the second level commands with the main menu command on the main menu. For example, press the button and after the tone say,
“Call Redial”.

© 2014-2026 Copyright www.nisentra.com