Nissan Sentra B18 (2020-2025) Service Manual: Wheel Alignment (unladen*1)
USA
|
Tire size |
205/60R16, 215/45R18 |
215/50R17 |
||
|
Camber Degree minute (Decimal degree) |
Minimum |
−1° 20′ 00′′ (−1.333°) |
−1° 20′ 00′′ (−1.333°) |
|
|
Nominal |
−0° 50′ 00′′ (−0.833°) |
−0° 50′ 00′′ (−0.833°) |
||
|
Maximum |
−0° 20′ 00′′ (−0.333°) |
−0° 20′ 00′′ (−0.333°) |
||
 |
||||
|
Total toe-in |
Distance (A - B) |
Minimum |
In 0.0 mm (In 0.000 in) |
Out 0.1 mm (Out 0.004 in) |
|
Nominal |
In 2.5 mm (In 0.098 in) |
In 2.4 mm (In 0.094 in) |
||
|
Maximum |
In 5.0 mm (In 0.200 in) |
In 4.9 mm (In 0.193 in) |
||
|
Angle (LH and RH)*2 Degree minute (Decimal degree) |
Minimum |
In 0° 00′ 00′′ (In 0.000°) |
In 0° 00′ 00′′ (In 0.000°) |
|
|
Nominal |
In 0° 13′ 00′′ (In 0.217°) |
In 0° 13′ 00′′ (In 0.217°) |
||
|
Maximum |
In 0° 26′ 00′′ (In 0.433°) |
In 0° 26′ 00′′ (In 0.433°) |
||
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard value.
Canada
|
Tire size |
205/60R16, 215/45R18 |
215/50R17 |
||
|
Camber Degree minute (Decimal degree) |
Minimum |
−1° 20′ 00′′ (−1.333°) |
−1° 20′ 00′′ (−1.333°) |
|
|
Nominal |
−0° 50′ 00′′ (−0.833°) |
−0° 50′ 00′′ (−0.833°) |
||
|
Maximum |
−0° 20′ 00′′ (−0.333°) |
−0° 20′ 00′′ (−0.333°) |
||
|
||||
|
Total toe-in |
Distance (A - B) |
Minimum |
Out 0.1 mm (Out 0.004 in) |
Out 0.2 mm (Out 0.008 in) |
|
Nominal |
In 2.4 mm (In 0.094 in) |
In 2.3 mm (In 0.091 in) |
||
|
Maximum |
In 4.9 mm (In 0.193) |
In 4.8 mm (In 0.189 in) |
||
|
Angle (LH and RH)*2 Degree minute (Decimal degree) |
Minimum |
In 0° 00′ 00′′ (In 0.000°) |
Out 0° 01′ 00′′ (In 0.017°) |
|
|
Nominal |
In 0° 13′ 00′′ (In 0.217°) |
In 0° 12′ 00′′ (In 0.200°) |
||
|
Maximum |
In 0° 26′ 00′′ (In 0.433°) |
In 0° 25′ 00′′ (In 0.417°) |
||
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard value.
Wheelarch Height (unladen)
Wheelarch Height (Unladen)
UNITED STATES
Unit: mm (in)
Tire size
205/60R16
...
Other materials:
Steering Switches
Exploded View
Exploded View
1.
Steering wheel
2.
Steering wheel finisher
3.
...
Ignition signal
Component Function Check
1.INSPECTION START
Turn ignition switch OFF.
Start engine.
Does the engine start?
YES >> GO TO 2.
NO >> Proceed to EC-456, "Diagnosis Procedure".
2.IGNITION SIGNAL FUNCTION
With CONSULT
Perform “POWER BALANCE” in “ACT ...
Description
NOTE:
This vehicle is diagnosed using the CONSULT-III plus.
When CONSULT is connected with a data link connector
equipped on the vehicle side, it will communicate with the control
unit equipped in the vehicle and then enable various kinds of diagnostic
tests.
Instrument lower panel LH ...
