Front Combination Lamp

Exploded View

Exploded View

1.

Front combination lamp

Removal and Installation

Removal and Installation

REMOVAL

Remove front bumper fascia. Refer to Removal and Installation.

Remove front combination lamp bolts.

Pull front combination lamp forward.

Disconnect harness connectors from front combination lamp and remove.

INSTALLATION

Installation is in the reverse order of removal.

Note:

After installation, perform headlamp aiming adjustment. Refer to Aiming Adjustment.

Bulb Replacement

Bulb Replacement

Warning:

Do not touch bulb with hand while it is lit or right after being turned off. Burning may result.

CAUTION:

• Do not touch glass surface of bulb with bare hands or allow oil or grease to get on it to prevent damage to bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture, smoke, etc. may affect performance of lamp. When replacing bulb, be sure to replace it with new one.

• After installing bulb, install bulb socket securely for watertightness.

HEADLAMP (LOW BEAM) BULB

The headlamp (low beam) bulb is LED and not serviced separately. Refer to Removal and Installation.

HEADLAMP (HIGH BEAM) BULB

The headlamp (high beam) bulb is LED and not serviced separately. Refer to Removal and Installation.

SIDE MARKER LAMP BULB

The side marker lamp bulb is LED and is serviced as an assembly to the front combination lamp. Refer to Removal and Installation.

DAYTIME RUNNING LAMP BULB

The daytime running lamp bulb is LED and is serviced as an assembly to the front combination lamp. Refer to Removal and Installation.

TURN/PARKING LAMP BULB

Removal

Remove front combination lamp. Refer to Removal and Installation.

Rotate turn/parking lamp bulb socket counterclockwise and remove from front combination lamp.

Remove turn/parking lamp bulb from bulb socket.

Front Fog Lamp

Exploded View

Exploded View

1.

Front bumper fascia

2.

Front fog lamp

Removal and Installation

Removal and Installation

Removal

Position the fender protector aside. Refer to Removal and Installation — Front Fender Protector.

Disconnect the harness connector from the front fog lamp.

Remove the screws and the front fog lamp.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

Bulb Replacement

The front fog lamp bulb is LED and is serviced as an assembly to the front fog lamp. Refer to Removal and Installation.

Door Mirror Turn Signal Lamp

Exploded View

Exploded View

1.	Door mirror assembly	2.	Door mirror base cover	3.	Side camera
4.	Door mirror turn signal lamp	5.	Door mirror housing	6.	Glass mirror
7.	Door mirror actuator	8.	Door mirror corner finisher	9.	Door mirror cover

Removal and Installation

Removal and Installation

Removal

Remove the side camera. Refer to Removal and Installation.

Remove screw (A) from the door mirror turn signal lamp (1).

Release the pawls on door mirror turn signal lamp (1).

: Pawl

Disconnect the harness connector and remove the door mirror turn signal lamp.

Bulb Replacement

Bulb Replacement

The door mirror turn signal lamp bulb is LED and is serviced as an assembly to the door mirror turn signal lamp. Refer to Removal and Installation.

High-Mounted Stop Lamp

Exploded View

Exploded View

1.	High-mounted stop lamp		Clip		Metal clip
	Front

Removal and Installation

Removal and Installation

HIGH-MOUNTED STOP LAMP

Removal

Slide high-mounted stop lamp (1) rearward on parcel shelf to provide clearance for front tabs (A).

Lift front of lamp assembly up and pull forward to provide clearance for rear tabs (B).

Disconnect the harness connector from the high-mounted stop lamp and remove.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

Bulb Replacement

HIGH-MOUNTED STOP LAMP

The high-mounted stop lamp bulb is LED and is serviced as an assembly to the high-mounted stop lamp. Refer to Removal and Installation.

License Plate Lamp

Exploded View

Exploded View

1.

License plate lamp

Clip

Removal and Installation

Removal and Installation

REMOVAL

Release the clip and remove the license plate lamp from the trunk lid.

Disconnect the harness connector from the license plate lamp and remove the license plate lamp.

INSTALLATION

Installation is in the reverse order of removal.

Bulb Replacement

Bulb Replacement

The license plate lamp bulb is serviced as an assembly to the license plate lamp. Refer to Removal and Installation.

Rear Combination Lamp (body Side)

Exploded View

Exploded View

1.	Rear combination lamp	A.	Grommet	B.	Clip
C.	Grommet

Removal and Installation

Removal and Installation

Removal

Partially remove trunk side finisher. Refer to Removal and Installation.

Remove the rear combination lamp nuts.

Disconnect the harness connector from the rear combination lamp.

Pull the rear combination lamp rearward and remove.

INSTALLATION

Installation is in the reverse order of removal.

Bulb Replacement

Bulb Replacement

Warning:

Do not touch bulb with bare hand while it is lit or right after being turned off. Burning may result.

CAUTION:

• Do not touch glass surface of bulb with bare hands or allow oil or grease to get on it to prevent damage to bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect performance of lamp. When replacing bulb, be sure to replace it with new one.

REAR TURN SIGNAL LAMP BULB

Removal

Remove the rear combination lamp. Refer to Removal and Installation.

Rotate the rear turn signal lamp bulb socket counterclockwise and remove.

Remove the rear turn signal lamp bulb from bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing, be sure to install the bulb socket securely to ensure watertightness.

STOP/TAIL LAMP

Removal

Remove the rear combination lamp. Refer to Removal and Installation.

Rotate the stop/tail lamp bulb socket counterclockwise and remove.

Remove the stop/tail lamp bulb from bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing, be sure to install the bulb socket securely to ensure watertightness.

Rear Combination Lamp (trunk Lid Side)

Exploded View

Exploded View

1.

Trunk lid

2.

Rear combination lamp (trunk lid side)

Removal and Installation

Removal and Installation

REMOVAL

Partially remove trunk lid trim. Refer to Removal and Installation.

Remove rear combination lamp (trunk lid side) nuts then remove rear combination lamp (trunk lid side).

INSTALLATION

Installation is in the reverse order of removal.

Bulb Replacement

Bulb Replacement

Warning:

Do not touch bulb with bare hand while it is lit or right after being turned off. Burning may result.

CAUTION:

• Do not touch glass surface of bulb with bare hands or allow oil or grease to get on it to prevent damage to bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect performance of lamp. When replacing bulb, be sure to replace it with new one.

TAIL LAMP BULB

REMOVAL

Remove the rear combination lamp. Refer to Removal and Installation.

Rotate the tail lamp bulb socket counterclockwise and remove.

Remove the tail lamp bulb from bulb socket.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

After installing, be sure to install the bulb socket securely to ensure watertightness.

BACK-UP LAMP BULB

REMOVAL

Remove the rear combination lamp (trunk lid side). Refer to Removal and Installation.

Rotate the back—up lamp bulb socket counterclockwise and remove.

Remove the back—up lamp bulb from bulb socket.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

After installing, be sure to install the bulb socket securely to ensure watertightness.

Combination Switch

Exploded View

Exploded View

1.	Steering column assembly	2.	Combination switch	A.	Screw
	Front

Note:

Shown with the steering wheel removed for clarity only.

Removal and Installation

Removal and Installation

REMOVAL

CAUTION:

Do not use air or electric tools when removing or installing the combination switch.

Remove the spiral cable. Refer to Removal and Installation.

Disconnect the harness connector from the combination switch.

Remove the screw from the combination switch and remove the combination switch.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.

• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function and delete the memory with CONSULT.

• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunctions. Refer to Description.

Hazard Switch

Exploded View

Exploded View

1.

Center ventilator grille

2.

Hazard switch

Pawl

Removal and Installation

Removal and Installation

REMOVAL

Remove center ventilator grille. Refer to Removal and Installation.

Release pawls and remove hazard switch (2) from center ventilator grille (1).

: Pawl

INSTALLATION

Installation is in the reverse order of removal.

Optical Sensor

Exploded View

Exploded View

1.	Optical sensor	2.	Mask	3.	Instrument panel assembly
	Pawl

Removal and Installation

Removal and Installation

REMOVAL

Using a suitable tool, release the optical sensor from the instrument panel assembly.

Disconnect the harness connector from the optical sensor and remove.

INSTALLATION

Installation is in the reverse order of removal.