Nissan Sentra B18 (2020-2025) Service Manual: Rear Suspension :: Service Data and Specifications (sds). Service Data and Specifications (sds)
Service Data and Specifications (sds). Wheel Alignment (unladen*1)
Wheel Alignment (Unladen*1)
USA
|
Tire size |
205/60R16, 215/45R18 |
215/50R17 |
||
|
Camber Degree minute (Decimal degree) |
Minimum |
−1° 20′ 00′′ (−1.333°) |
−1° 20′ 00′′ (−1.333°) |
|
|
Nominal |
−0° 50′ 00′′ (−0.833°) |
−0° 50′ 00′′ (−0.833°) |
||
|
Maximum |
−0° 20′ 00′′ (−0.333°) |
−0° 20′ 00′′ (−0.333°) |
||
![]() |
||||
|
Total toe-in |
Distance (A - B) |
Minimum |
In 0.0 mm (In 0.000 in) |
Out 0.1 mm (Out 0.004 in) |
|
Nominal |
In 2.5 mm (In 0.098 in) |
In 2.4 mm (In 0.094 in) |
||
|
Maximum |
In 5.0 mm (In 0.200 in) |
In 4.9 mm (In 0.193 in) |
||
|
Angle (LH and RH)*2 Degree minute (Decimal degree) |
Minimum |
In 0° 00′ 00′′ (In 0.000°) |
In 0° 00′ 00′′ (In 0.000°) |
|
|
Nominal |
In 0° 13′ 00′′ (In 0.217°) |
In 0° 13′ 00′′ (In 0.217°) |
||
|
Maximum |
In 0° 26′ 00′′ (In 0.433°) |
In 0° 26′ 00′′ (In 0.433°) |
||
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard value.
Canada
|
Tire size |
205/60R16, 215/45R18 |
215/50R17 |
||
|
Camber Degree minute (Decimal degree) |
Minimum |
−1° 20′ 00′′ (−1.333°) |
−1° 20′ 00′′ (−1.333°) |
|
|
Nominal |
−0° 50′ 00′′ (−0.833°) |
−0° 50′ 00′′ (−0.833°) |
||
|
Maximum |
−0° 20′ 00′′ (−0.333°) |
−0° 20′ 00′′ (−0.333°) |
||
![]() |
||||
|
Total toe-in |
Distance (A - B) |
Minimum |
Out 0.1 mm (Out 0.004 in) |
Out 0.2 mm (Out 0.008 in) |
|
Nominal |
In 2.4 mm (In 0.094 in) |
In 2.3 mm (In 0.091 in) |
||
|
Maximum |
In 4.9 mm (In 0.193) |
In 4.8 mm (In 0.189 in) |
||
|
Angle (LH and RH)*2 Degree minute (Decimal degree) |
Minimum |
In 0° 00′ 00′′ (In 0.000°) |
Out 0° 01′ 00′′ (In 0.017°) |
|
|
Nominal |
In 0° 13′ 00′′ (In 0.217°) |
In 0° 12′ 00′′ (In 0.200°) |
||
|
Maximum |
In 0° 26′ 00′′ (In 0.433°) |
In 0° 25′ 00′′ (In 0.417°) |
||
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard value.
Wheelarch Height (unladen)
Wheelarch Height (Unladen)
UNITED STATES
Unit: mm (in)![]() |
|||
|---|---|---|---|
|
Tire size |
205/60R16 |
215/50R17 |
215/45R18 |
|
Front (Hf) |
684 (26.93) |
683 (26.89) |
686 (27.01) |
|
Rear (Hr) |
685 (26.97) |
684 (26.93) |
687 (27.05) |
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
CANADA
Unit: mm (in)![]() |
|||||
|---|---|---|---|---|---|
|
Transaxle |
MT |
CVT |
|||
|
Tire size |
205/60R16 |
215/45R18 |
205/60R16 |
215/50R17 |
215/45R18 |
|
Front (Hf) |
686 (27.01) |
688 (27.09) |
685 (26.97) |
684 (26.93) |
687 (27.05) |
|
Rear (Hr) |
686 (27.01) |
688 (27.09) |
686 (27.01) |
685 (26.97) |
688 (27.09) |
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
Other materials:
Fuel Injector
Component Function Check
Component Function Check
INSPECTION START
Turn ignition switch to START.
Are any cylinders ignited?
YES >>
GO TO
2.
NO >>
Refer to Diagnosis Procedure.
CHECK FUEL INJECTOR FUNCTION
...
Additional Service When Replacing Transaxle Assembly
Description
Description
Perform the following work when the transaxle assembly is
replaced. For work procedure, refer to Work Procedure.
WORK BEFORE TRANSAXLE ASSEMBLY REPLACEMENT
New transaxle assembly serial number checking
WORK AFTER TRANSAXLE ASSEMBLY REPLACEMENT
Cal ...
Brake System. Periodic Maintenance Operation
Periodic Maintenance Operation
Periodic Maintenance Operation
ADJUSTMENT
CAUTION:
Burnish the brake contact surfaces after
refinishing or replacing rotors, after replacing pads, after
refinishing or replacing drums, after replacing shoes, or if a soft
...

