S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P2815-00 Select Solenoid

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P2815

00

SELECT SOLENOID

(Pressure Control Solenoid "G" Control Circuit High)

Diagnosis condition

Power supply voltage > 10 V

Signal

Select solenoid valve drive signal

Threshold

When solenoid valve drive circuit is diagnosed as short to the battery

Diagnosis detection time

0.2 seconds

POSSIBLE CAUSE

  • Harness or connector

  • Select solenoid valve

  • TCM

FAIL-SAFE

  • Powertrain becomes neutral

  • Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

  1. PREPARATION BEFORE WORK

    If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is more than 10 V.

    >>

    GO TO 2.

  2. CHECK DTC DETECTION

    1. Start the engine.

    2. Depress the brake pedal.

    3. Shift the selector lever to "R" position and wait for 5 seconds or more.

    4. Shift the selector lever to "N" position and wait for 5 seconds or more.

    5. Shift the selector lever to "D" position and wait for 5 seconds or more.

    6. Shift the selector lever to "L" position and wait for 5 seconds or more.

    7. Shift the selector lever to "P" position and wait for 5 seconds or more.

    8. Check the DTC

    Is "P2815-00" detected?

    YES >>

    Proceed to Diagnosis Procedure.

    NO-1>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2>>

    Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK SELECT SOLENOID VALVE CIRCUIT

    Check select solenoid valve circuit. Refer to Diagnosis Procedure.

    Is the inspection result normal?

    YES >>

    Replace TCM. Refer to Removal and Installation.

    NO >>

    Repair or replace damaged parts.

    P2814-00 Select Solenoid
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2814 00 SELECT SOLENOID (Pressure Control Solen...
    P28ed-00 Electric Oil Pump
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P28ED 00 EL/AUX T/M FLUID PUMP B (Electric/Auxil...

    Other materials:

    Instrument Panel. Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Squeak and Rattle Trouble Diagnoses Work Flow Work Flow CUSTOMER INTERVIEW Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occu ...

    Low Tire Pressure Location Indicator Does Not Display
    Symptom Description Symptom Description When there is low tire pressure, the low tire location indicator does not display even though the low tire pressure warning lamp turns ON. Diagnosis Procedure Diagnosis Procedure Note: The Signal Tech II Tool [– (NI-50190)] can be used to ...

    Rear Side Air Bag Module. Removal and Installation
    Removal and Installation Removal and Installation Warning: Before servicing the SRS, place the ignition switch in the OFF position, disconnect both battery terminals then wait at least three minutes. Do not use air tools or electric ...