Nissan Sentra B18 (2020-2025) Service Manual: P2100 Throttle Control Motor Relay
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
|
|
P2100 |
ETC MOT PWR-B1 (Throttle actuator “A� control motor circuit/open) |
Diagnosis condition |
Engine running at idle |
|
Signal (terminal) |
Throttle control motor relay signal |
||
|
Threshold |
ECM detects a voltage of power source for throttle control motor is excessively low |
||
|
Diagnosis delay time |
— |
||
POSSIBLE CAUSE
-
Harness or connectors (Throttle control motor relay circuit is open.)
-
Throttle control motor relay
FAIL-SAFE
Engine Control System
|
Engine operating condition in fail-safe mode |
||
|---|---|---|
|
Fail safe mode |
Nissan Sentra Vehicle behavior |
|
|
Device fix mode |
|
|
|
Others |
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring. |
|
Idle Start/Stop System
When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.
When ECM detects error while operating the idle start/stop system, ECM restarts the engine.
Confirmation Procedure
Confirmation Procedure
-
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
Witch DTC is detected?
P2100>>GO TO 2.
P2103>>GO TO 3.
-
-
PERFORM DTC CONFIRMATION PROCEDURE-DTC P2100
-
Turn ignition switch ON and wait at least 2 seconds.
-
Start engine and let it idle for 5 seconds.
-
Check DTC.
Is DTC detected?
YES >>Proceed to DTC Diagnosis Procedure.
NO-1 >>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>Confirmation after repair: INSPECTION END
-
-
PERFORM DTC CONFIRMATION PROCEDURE-DTC P2103
-
Turn ignition switch ON and wait at least 1 second.
-
Check DTC.
Is DTC detected?
YES >>Proceed to DTC Diagnosis Procedure.
NO-1 >>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>Confirmation after repair: INSPECTION END
-
Dtc Diagnosis Procedure
DTC Diagnosis Procedure
-
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY
-
Turn ignition switch ON.
-
Check the voltage between ECM harness connectors.
+
−
Voltage
(Approx.)
ECM
Connector
Terminal
Connector
Terminal
F25
128
E16
162
Battery voltage
Is the inspection result normal?
YES >>GO TO 3.
NO >>GO TO 2.
-
-
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT
-
Turn ignition switch OFF.
-
Disconnect ECM harness connector.
-
Disconnect IPDM E/R harness connector.
-
Check the continuity between ECM harness connector and IPDM E/R harness connector.
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F25
128
F96
72
Existed
-
Also check harness for short to ground and to power.
Is the inspection result normal?
YES >>Perform the trouble diagnosis for power supply circuit.
NO >>Repair or replace malfunctioning part.
-
-
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL
-
Turn ignition switch OFF.
-
Check the voltage between ECM harness connectors.
+
−
Condition
Voltage
(Approx.)
ECM
Connector
Terminal
Connector
Terminal
F25
97
E16
162
Ignition switch
OFF
0 V
ON
Battery voltage
Is the inspection result normal?
YES >>INSPECTION END
NO >>GO TO 4.
-
-
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT
-
Turn ignition switch OFF.
-
Disconnect ECM harness connector.
-
Disconnect IPDM E/R harness connector.
-
Check the continuity between ECM harness connector and IPDM E/R harness connector.
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F25
97
F96
67
Existed
-
Also check harness for short to ground and to power.
Is the inspection result normal?
YES >>INSPECTION END
NO >>Repair or replace malfunctioning part.
-
Other materials:
Removal and Installation
Av Control Unit
Exploded View
Exploded View
1.
AV control unit bracket
(LH)
2.
AV control unit
...
Seat belt warning light and chime
The driver and front passenger seats in the Nissan Sentra are equipped with an
enhanced seat belt reminder system. When this feature is active, both a visual warning
and an audible chime will operate if the driver or front passenger seat belt remains
unbuckled while the vehicle is travelin ...
Brake System. Service Data and Specifications (sds). Service Data and Specifications (sds)
Service Data and Specifications (sds)
General Specifications
General Specifications
Unit: mm (in)
Master cylinder
Cylinder bore diameter
25.4 (1)
...