Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P1212 Tcs Communication Line

Nissan Sentra B18 (2020-2025) Service Manual: P1212 Tcs Communication Line

Dtc Description

DTC Description

This CAN communication line is used to control the smooth engine operation during the TCS operation. Pulse signals are exchanged between ECM and “ABS actuator and electric unit (control unit)”.

Be sure to erase the malfunction information such as DTC not only for “ABS actuator and electric unit (control unit)” but also for ECM after TCS related repair.
Freeze frame data is not stored in the ECM for this self-diagnosis.

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P1212	TCS/CIRC (TCS/CIRC)	Diagnosis condition	Engine running at idle
		Signal (terminal)	CAN communication signal
		Threshold	ECM cannot receive the information from “ABS actuator and electric unit (control unit)” continuously
		Diagnosis delay time	—

POSSIBLE CAUSE

Harness or connectors (CAN communication line is open or shorted.)
ABS actuator and electric unit (control unit)
Dead (Weak) battery

FAIL-SAFE

Not applicable

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1212 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable.
- DTC UXXXX: Refer to DTC Index.
- DTC P0607: Refer to DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1212 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable.
- DTC UXXXX: Refer to DTC Index.
- DTC P0607: Refer to DTC Description.
NO >>
GO TO 2.
PERFORM BASIC INSPECTION TO CHECK THE BRAKE CONTROL SYSTEM

Perform basic inspection to check the brake control system. Refer to Work Procedure.

>>
Repair or replace malfunctioning part.

 P119c Fuel Rail Pressure Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P119C FUEL PRESSURE SENSOR (Fuel pressure sensor...

 P1217 Engine Over Temperature

Dtc Description DTC Description ECM controls cooling fan to the maximum speed when receives the signal abnormality of each sensor, CAN and IPDM E/R, and severed wire short circu...

Other materials:

Component Parts
Rear Automatic Braking System Component Parts Location Component Parts Location A. Right side of instrument panel (view with glove box assembly removed) ...

B2070-68 Key Registration
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition ...

Heated seat switches
WARNING Do not use the seat heater, or allow passengers to use it, if you or they cannot monitor elevated seat temperatures or have reduced sensitivity to pain in body areas contacting the seat. Use of the heated seats under these conditions could result in serious injury. CAUTION Th ...