Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0606 Ecm

Nissan Sentra B18 (2020-2025) Service Manual: P0606 Ecm

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0606	CONTROL MODULE (Control module processor)	Diagnosis condition	—
		Signal (terminal)	—
		Threshold	Malfunction in ECM processor
		Diagnosis delay time	—

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE-1
1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds.
  
  CAUTION:
  
  Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Proceed to DTC Diagnosis Procedure.
NO >>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE-2
1. Start the engine.
2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release the accelerator pedal.
3. Let the engine idle and wait at least 10 seconds.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Turn ignition switch ON.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Proceed to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure for 3 times. Refer to Confirmation Procedure.
Is the 1st trip DTC P0606 displayed again?
YES >>
Replace ECM. Refer to ECM : Removal & Installation.
NO >>
INSPECTION END

 P0604 Ecm

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0604 ECM [Internal control module random access...

 P0607 Ecm

Dtc Description DTC Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Sentra vehicle multiplex communication...

Other materials:

U1112-24 Deceleration Request Signal
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection ...

Parking Brake System. Foot Pedal with Rear Drum Brakes
Precaution. Precautions Precautions Precaution for Supplemental Restraint System (srs) "air Bag" and "seat Belt Pre-Tensioner" Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BEL ...

System
System Description System Description SYSTEM DIAGRAM AV Control Unit Input Signal (AV Communication) Transmit unit Signal name Combination meter ...