Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0604 Ecm

Nissan Sentra B18 (2020-2025) Service Manual: P0604 Ecm

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0604	ECM [Internal control module random access memory (RAM) error]	Diagnosis condition	Ignition switch ON
		Signal (terminal)	—
		Threshold	Malfunction in the internal RAM of ECM
		Diagnosis delay time	—

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Device fix mode	This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Others	(Computing part of ECM does not operate normally.) ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Engine operating condition in fail-safe mode

Fail safe mode

Nissan Sentra Vehicle behavior

Device fix mode

This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the reference position.
The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).

Others

(Computing part of ECM does not operate normally.)

ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 20 minutes.
  
  CAUTION:
  
  Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Proceed to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to Confirmation Procedure.
Is the 1st trip DTC P0604 displayed again?
YES >>
Replace ECM. Refer to ECM : Removal & Installation.
NO >>
INSPECTION END

 P0603 Ecm

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0603 ECM BACK UP/CIRCUIT [Internal Control Modu...

 P0606 Ecm

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0606 CONTROL MODULE (Control module processor) ...

Other materials:

Intelligent Key Unit. Removal and Installation
Removal and Installation Removal and Installation REMOVAL CAUTION: Be sure to perform “ADDITIONAL SERVICE WHEN REPLACING INTELLIGENT KEY UNIT” when replacing Intelligent Key unit. Refer to Work Procedure. Remove instrument panel assembly. Refer to Removal and ...

B0012-55 Active Vent
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition ...

B1360 Combination Meter
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...