Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: P0605 Ecm

Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0605 Ecm

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0605

ECM

[Internal control module read only memory (ROM) error]

Diagnosis condition

Ignition switch ON

Signal (terminal)

—

Threshold

Malfunction in the internal ROM of ECM

Diagnosis delay time

—

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode

Fail safe mode

Nissan Sentra Vehicle behavior

Device fix mode

  • This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the reference position.

  • The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).

Others

(Computing part of ECM does not operate normally.)

ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

  1. PRECONDITIONING

    1. Turn ignition switch OFF and wait at least 10 seconds.

    2. Turn ignition switch ON.

    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

    >>

    GO TO 2.

  2. PERFORM DTC CONFIRMATION PROCEDURE

    1. Turn ignition switch ON (engine stopped) and wait least 20 minutes.

      CAUTION:

      Never start engine during this procedure.

    2. Turn ignition switch OFF and wait at least 10 seconds.

    3. Turn ignition switch ON.

    4. Check 1st trip DTC.

    Is 1st trip DTC detected?

    YES >>

    Proceed to DTC Diagnosis Procedure.

    NO-1 >>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2 >>

    Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. INSPECTION START

    1. Erase self-diagnostic results. Refer to Diagnosis Description.

    2. Perform “DTC Confirmation Procedure”. Refer to Confirmation Procedure.

    Does 1st trip DTC P0605 duplicated?

    YES >>

    Replace ECM. Refer to ECM : Removal & Installation.

    NO >>

    INSPECTION END

P0604 Ecm
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

P0606 Ecm
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

Other materials:

Vehicle Recovery (Freeing a Stuck Vehicle)
Front Remove the hook cover from the bumper using a remover tool. Securely install the vehicle recovery hook stored with jacking tools. Check that the hook is properly secured in the stored place after use. WARNING: Stand clear of a stuck vehicle. Do not spin your tires at high s ...

Precaution
Precaution for supplemental restraint system (srs) "air bag" and "seat belt pre-tensioner" The supplemental restraint system such as “air bag” and “seat belt pre-tensioner”, used along with a front seat belt, helps to reduce the risk or severity of inju ...

Warning Chime System
Component Parts Location Component Parts Location MODELS WITH CVT No. Component Function 1. ...

© 2014-2026 Copyright www.nisentra.com