Nissan Sentra B18 (2020-2025) Service Manual: P0451 Evap Control System Pressure Sensor
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
|
|
P0451 |
Barometric pressure sensor A/B (EVAP System Pressure Sensor/Switch "A" Circuit Range/Performance |
Diagnosis condition |
Ignition switch ON |
|
Signal (terminal) |
EVAP control system pressure sensor signal |
||
|
Threshold |
ECM detects a state that the pressure difference remains the threshold value or more for continuously for 5 seconds or more under the condition that the pressure of the EVAP control system pressure sensor and that of the Barometric pressure sensor are equal. |
||
|
Diagnosis delay time |
3 seconds or more |
||
POSSIBLE CAUSE
-
EVAP control system pressure sensor
-
Barometric pressure sensor (builtinto ECM)
-
Clogging, crushing, or damage in hose or piping.
FAIL-SAFE
Not applicable
Confirmation Procedure
Confirmation Procedure
-
CHECK DTC PRIORITY
If DTC P0451 is displayed with DTC P0452 or P0453, first perform the trouble diagnosis for DTC P0452 or P0453.
Is DTC P0452, or P0453 detected?
YES >>Perform diagnosis of applicable.
-
DTC P0452: Refer to DTC Description.
-
DTC P0453: Refer to DTC Description.
GO TO 2.
-
-
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
GO TO 3.
-
-
PERFORM DTC CONFIRMATION PROCEDURE
-
Turn ignition switch ON.
-
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>Proceed to DTC Diagnosis Procedure.
NO-1 >>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>Confirmation after repair: INSPECTION END
-
Dtc Diagnosis Procedure
DTC Diagnosis Procedure
-
CHECK HOSE AND PIPING
-
Turn ignition switch OFF.
-
Check the following.
-
Blockage, crush, or damage in the hose and the piping of EVAP purge line between fuel tank and intake manifold.
-
Blockage, crush, or damage in the hose and the piping of intake air passage between inlet air duct and intake manifold.
-
Is the inspection result normal?
YES >>GO TO 2.
NO >>Repair or replace error-detected parts.
-
-
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check EVAP control system pressure sensor.
Is the inspection result normal?
YES >>GO TO 3.
NO >>Replace EVAP control system pressure sensor.
-
CHECK BAROMETRIC PRESSURE SENSOR
Check barometric pressure sensor. Refer to Component Inspection.
Is the inspection result normal?
YES >>Check intermittent incident. Refer to Intermittent Incident.
NO >>Repair or replase malfunctioning part. Refer to Removal & Installation.
Other materials:
Camera Aiming Adjustment
Work Procedure
Work Procedure
Always adjust the camera aiming after removing and
installing or replacing the front camera unit.
Always adjust the camera aiming after removing and
installing or replacing the windshield glass.
CAUTION:
...
Intelligent Key Button Operation Has Poor Range (one Key)
Description
Description
Intelligent Key button operation has poor range.
(One Intelligent Key has the symptom, other keys operate
normally.)
SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE
SYMPTOM, OTHER KEYS OPERATE NORMALLY)
...
B1040-22 Vehicle Speed
Dtc Description
DTC Description
DTC DETECTION LOGIC
Note:
This DTC may be detected when drive the Nissan Sentra vehicle
at vehicle speed of 186 MPH (300 km/h) or more.
DTC No.
CONSULT sc ...