Nissan Sentra B18 (2020-2025) Service Manual: P044c Egr Volume Control Valve Position Sensor
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
|
|
P044C |
EGR SENSOR C (EGR sensor C circuit low) |
Diagnosis condition |
Ignition switch ON |
|
Signal (terminal) |
EGR volume control valve position sensor |
||
|
Threshold |
ECM detects the following status continuously for 5 seconds or more; A voltage signal transmitted from the EGR volume control valve position sensor shows too low. |
||
|
Diagnosis delay time |
— |
||
POSSIBLE CAUSE
-
Harness or connectors
(EGR volume control valve position sensor circuit is open or shorted.)
-
EGR volume control valve
FAIL-SAFE
Engine Control System
|
Engine operating condition in fail-safe mode |
||
|---|---|---|
|
Fail safe mode |
Nissan Sentra Vehicle behavior |
|
|
Traveling control mode |
Accelerator angle variation control |
ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction. Note:
ECM does not control the accelerator pedal releasing speed. |
|
Device fix mode |
|
|
Idle Start/Stop System
Not applicable
Confirmation Procedure
Confirmation Procedure
-
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
GO TO 2.
-
-
PERFORM DTC CONFIRMATION PROCEDURE
-
Turn ignition switch ON and wait at least 5 seconds.
-
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>Proceed to DTC Diagnosis Procedure.
NO >>INSPECTION END
-
Dtc Diagnosis Procedure
DTC Diagnosis Procedure
-
CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR POWER SUPPLY
-
Turn ignition switch OFF.
-
Disconnect EGR volume control valve harness connector.
-
Turn ignition switch ON.
-
Check voltage between EGR volume control valve harness connector and ground.
+
−
Voltage
(Approx.)
EGR volume control valve
Connector
Terminal
F94
3
Ground
5 V
Is the inspection result normal?
YES >>GO TO 2.
NO >>GO TO 5.
-
-
CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR GROUND CIRCUIT
-
Turn ignition switch OFF.
-
Disconnect ECM harness connector.
-
Check harness continuity between EGR volume control valve harness connector and ECM harness connector.
EGR volume control valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
2
F25
79
Existed
-
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >>GO TO 3.
NO >>Repair or replace error-detected parts.
-
-
CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT
-
Check harness continuity between EGR volume control valve harness connector and ECM harness connector.
EGR volume control valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
1
F25
78
Existed
-
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >>GO TO 4.
NO >>Repair or replace error-detected parts.
-
-
CHECK EGR VOLUME CONTROL VALVE
Check the EGR volume control valve. Refer to Component Inspection.
Is the inspection result normal?
YES >>Check intermittent incident. Refer to Intermittent Incident.
NO >>Replace EGR volume control valve. Refer to Exploded View.
-
CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT
-
Turn ignition switch OFF.
-
Disconnect ECM harness connector.
-
Check the continuity between EGR volume control valve harness connector and ECM harness connector.
EGR volume control valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F94
3
F25
83
Existed
-
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >>Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.
NO >>Repair or replace error-detected parts.
-
Other materials:
Maintenance precautions
When performing any inspection, servicing, or maintenance work on your Nissan
Sentra, always exercise extreme care to avoid serious personal injury or accidental
damage to the vehicle. Routine maintenance plays an important role in the long-term
reliability, safety, and performance of the Niss ...
Consult Checking System
Description
Description
Note:
This vehicle is diagnosed using the CONSULT-III
plus.
When CONSULT is connected with a data link connector equipped on the
Nissan Sentra vehicle side, it will
communicate with the control unit equipped in the vehicle and then
...
U1040 Eng Comm Circuit
Dtc Description
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis
content)
DTC detection
condition
...