Additional Service When Replacing Ipdm E/r

Work Procedure

Work Procedure

After replacing the IPDM E/R, it is necessary to perform control unit configuration with CONSULT.

BEFORE REPLACEMENT

Before replacing IPDM E/R, save or print current Nissan Sentra vehicle specification with CONSULT vehicle configuration.

If the Nissan Sentra vehicle specifications cannot be saved, replace the IPDM E/R and then write the vehicle specifications by “Manual selection”.

AFTER REPLACEMENT

When replacing IPDM E/R, write Nissan Sentra vehicle specification with CONSULT vehicle configuration.

CAUTION:

Never perform vehicle configuration other than performing with a new IPDM E/R or the control function may not operate normally.

1. SAVING Nissan Sentra Vehicle SPECIFICATION

   1. CONSULT

      1. Ignition switch ON.

      2. Select the “IPDM E/R” of “Re/programming, Configuration”.

      3. Select the “Before ECU Replacement” of “Nissan Sentra Vehicle Configuration” to save current vehicle specification.

      Note:

      If Nissan Sentra vehicle specification cannot be saved with “Before ECU Replacement” of “Vehicle Configuration”, perform “After ECU Replacement” of “Manual selection” to write Nissan Sentra vehicle specification.

   >>

   GO TO 2.

2. REPLACE IPDM E/R

   1. 1. Ignition switch OFF.

      2. Replace IPDM E/R. Refer to Removal and Installation.

   >>

   GO TO 3.

3. WRITING Nissan Sentra Vehicle SPECIFICATION

   1. CONSULT

      1. Ignition switch ON.

      2. Select the “IPDM E/R” of “Re/programming, Configuration”.

      3. Select the Nissan Sentra vehicle specifications saved with “Before ECU Replacement” and then write them to the replacement IPDM E/R. Refer to Work Procedure.

   >>

   Work End.

Configuration (ipdm E/r)

Work Procedure

Work Procedure

There is no vehicle specification in the new IPDM E/R, so the vehicle specification needs to be written in IPDM E/R with CONSULT.

Configuration has three functions as follows:

Function		Description
Before ECU Replacement		Reads the Nissan Sentra vehicle configuration of current IPDM E/R Saves the read vehicle configuration
After ECU Replacement	FAST linked	Note: This item is displayed, but cannot be used
	Manual selection	Writes the Nissan Sentra vehicle configuration with manual selection.

CAUTION:

Never perform Nissan Sentra vehicle configuration other than performing with a new IPDM E/R or the control function may not operate normally.

1. WRITING MODE SELECTION

   1. CONSULT

      Reads the Nissan Sentra vehicle specification.

   When writing saved data (able to be read)>>

   GO TO 2.

   When writing manually (could not be read)>>

   GO TO 3.

2. PERFORM WRITING SAVED DATA

   1. CONSULT

      1. Ignition switch ON.

      2. Select “Re/programming, Configuration”. Select the Nissan Sentra vehicle specifications saved with “Before ECU Replacement” and then write them to the replacement IPDM E/R.

   >>

   GO TO 5.

3. PERFORM WRITING MANUALLY (IPDM E/R)

   1. CONSULT

      1. Ignition switch ON.

      2. Select the “IPDM E/R” of “Re/programming, Configuration”.

      3. Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the IPDM E/R.

         CAUTION:

         Check the “Type ID” accurately. If the “Type ID” is selected incorrectly, ECU control may not function normally.

   >>

   GO TO 4

4. OPERATION CHECK

   1. Confirm that each function controlled by IPDM E/R operates normally.

   >>

   Work End.

Work Item List

Work Item List

• Thoroughly read and understand the vehicle specification. ECU control may not operate normally if the setting is not correct.

• The “Setting Value” of this Nissan Sentra vehicle is as follows: Never select any other value than the setting value shown below (if there is only 1 item in “Setting Value” that means that item is the only choice for this certain Nissan Sentra vehicle).