Nissan Sentra B18 (2020-2025) Service Manual / Driver Controls / Exterior Lighting System :: Led Headlamp / Dtc/circuit Diagnosis / B20d4-11 Tail Lamp Lh Pwr Sply Circ

Nissan Sentra B18 (2020-2025) Service Manual: B20d4-11 Tail Lamp Lh Pwr Sply Circ

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items (Trouble diagnosis content)		DTC detection condition
B20D4–11	TAIL LAMP LH PWR SPLY CIRC (Tail lamp left hand power supply circuit)	[CIRCUIT SHORT TO GROUND]	Diagnosis condition	When the parking lamp, license plate lamp, side marker lamp and tail lamp ON conditions are satisfied (Smart FET inside IPDM E/R is ON)
			Signal (terminal)	The following power supply circuit: Tail lamp LH Tail lamp RH License plate lamp LH License plate lamp RH Front side marker lamp LH Front side marker lamp RH
			Threshold	Overcurrent is detected
			Diagnosis delay time	1 second or less

POSSIBLE CAUSE

Harness or connector
Tail lamp LH (body side) bulb
Tail lamp LH (body side) bulb socket or harness
Tail lamp RH (body side) bulb
Tail lamp RH (body side) bulb socket or harness
Tail lamp LH (trunk lid side) bulb
Tail lamp LH (trunk lid side) bulb socket or harness
Tail lamp RH (trunk lid side) bulb
Tail lamp RH (trunk lid side) bulb socket or harness
License plate lamp LH bulb
License plate lamp RH bulb
Front combination lamp LH
- LED (front side marker lamp)
Front combination lamp RH
- LED (front side marker lamp)
IPDM E/R

FAIL-SAFE

Shuts off the power supply to the tail lamp (LH/RH) circuits until the parking lamp, license plate lamp, side marker lamp and tail lamp ON conditions are no longer satisfied.

Dtc Confirmation Procedure

DTC Confirmation Procedure

PRECONDITIONING

CONSULT

Ignition switch ON.
Select “T LAMP LH CIRC MALFUNCTN” and “T LAMP RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R”.

Check the monitor status.

Monitor item	Monitor status
T LAMP LH CIRC MALFUNCTN	0
T LAMP LH CIRC MALFUNCTN	1
T LAMP RH CIRC MALFUNCTN	0
T LAMP RH CIRC MALFUNCTN	1

What is the monitor status?

“0”>>

GO TO 2.

“1”>>

A short circuit is detected multiple times in the tail lamp LH, tail lamp RH, license plate lamp LH or license plate lamp RH power supply circuit, and damage accumulates at the Smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn ON the Smart FET. Because the DTC cannot be reproduced in this state, refer to DTC Diagnosis Procedure and replace IPDM E/R after the malfunctioning part is repaired. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE
1. CONSULT
  1. Ignition switch OFF.
  2. Ignition switch ON.
  3. Turn lighting switch 1ST.
  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.
  5. Check DTC.
Is DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>
Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK TAIL LAMP POWER SUPPLY CIRCUIT (SHORT)

Ignition switch OFF.
Disconnect the following connectors:
- IPDM E/R
- Front combination lamp LH
- Front combination lamp RH
- Rear combination lamp LH (body side)
- Rear combination lamp LH (trunk lid side)
- Rear combination lamp RH (body side)
- Rear combination lamp RH (trunk lid side)
- License plate lamp LH
- License plate lamp RH

Check continuity between IPDM E/R harness connector and ground.

IPDM E/R		—	Continuity
Connector	Terminal	—	Continuity
E47	4	Ground	No
E47	17	Ground	No

Is the inspection result normal?

YES >>

GO TO 2.

NO >>

Repair or replace harness.

CHECK TAIL LAMP POWER SUPPLY

CONSULT

Connect IPDM E/R connector.
Ignition switch ON.
Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R”.

With operating the test item, check voltage between rear combination lamp (body side) harness connector and ground.

+			-	Test item		Voltage (Approx.)
Rear combination lamp (body side)
Connector		Terminal
RH	B42	2	Ground	TAIL LAMP	On	Battery voltage
RH	B42				Off	0V
LH	B25				On	Battery voltage
LH	B25				Off	0V

Is the inspection result normal?

YES >>

GO TO 3.

NO >>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK TAIL LAMP
1. Check the tail lamp. Refer to Component Inspection.
Is the inspection result normal?
YES >>
GO TO 4.
NO >>
Repair or replace the malfunctioning part.
CHECK LICENSE PLATE LAMP
1. Check the license plate lamp. Refer to Component Inspection.
Is the inspection result normal?
YES >>
GO TO 5.
NO >>
Repair or replace the malfunctioning part.
CHECK FRONT SIDE MARKER LAMP
1. Check the front side marker lamp. Refer to Component Inspection.
Is the inspection result normal?
YES >>
Inspection End.
NO >>
Repair or replace the malfunctioning part.

 B20ce-15 Hl (hi) Lh Pwr Sply Circ

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B20CE-15 HL (HI) LH PWR SPLY CIRC [Headlamp ...

 B20e2-96 Led Headlamp Rh

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B20E2–96 LED HEADLAMP RH (Light emitting d...

Other materials:

Car phone or CB radio
When installing a CB radio, ham radio, or car phone in the Nissan Sentra, always observe the precautions listed below. Improper installation may negatively affect the engine control system and other electronic components of the vehicle. WARNING A cellular phone should not be used for any pu ...

Radio
Place the ignition switch in the ACC or ON position and press the PUSH button to switch the radio on. When listening to the radio in your Nissan Sentra with the engine turned off, always keep the ignition switch in the ACC position to avoid unnecessary battery discharge. Radio reception qua ...

Main Line Between Icc 2 and Rdr-L Circuit
Diagnosis Procedure Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and ...