Nissan Sentra manuals

Nissan Sentra Service Manual: C1121, C1123, C1125, C1127 ABS OUT Valve system

Nissan Sentra Service Manual / Brakes / Brake control system / Dtc/circuit diagnosis / C1121, C1123, C1125, C1127 ABS OUT Valve system

DTC Logic

DTC DETECTION LOGIC

DTC DETECTION LOGIC

Display Item

Malfunction detected condition

Possible causes

C1121 FR LH OUT ABS SOL When a malfunction is detected in front LH ABS OUT valve.
  • Harness or connector
  • ABS actuator and electric unit (control unit)
  • Fusible link
  • Battery power supply system
C1123 FR RH OUT ABS SOL When a malfunction is detected in front RH ABS OUT valve.
C1125 RR LH OUT ABS SOL When a malfunction is detected in rear LH ABS OUT valve.
C1127 RR RH OUT ABS SOL When a malfunction is detected in rear RH ABS OUT valve.

DTC CONFIRMATION PROCEDURE

1.CHECK SELF DIAGNOSTIC RESULT

With CONSULT


  1. Turn ignition switch ON.

  2. Perform self diagnostic result.

Is DTC C1121, C1123, C1125 or C1127 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-74, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-44, "Wiring Diagram".

1.CONNECTOR INSPECTION

  1. Turn ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) connector.

  3. Check connector and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace as necessary.

2.Check ABS Actuator and electric unit (control unit) battery power supply

Check voltage between ABS actuator and electric unit (control unit) connector E33 terminal 25 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning components.

3.Check abs actuator and electric unit (control unit) ground circuit

Check continuity between ABS actuator and electric unit (control unit) connector E33 terminals 13, 38 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-110, "Removal and Installation".

NO >> Repair or replace malfunctioning components.

C1120, C1122, C1124, C1126 ABS In valve system
DTC Logic Dtc detection logic DTC Display Item Malfunction detected condition Possible causes C1120 FR LH IN ABS SOL When a malfunction is detected in front LH ABS IN ...

C1130 Engine signal
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1130 ENGINE SIGNAL 1 When a malfunction is detected in ECM system. ...

Other materials:

L terminal circuit (open)
Description The “L” terminal circuit controls the charge warning lamp. The charge warning lamp turns ON when the ignition switch is set to ON or START. When the generator is providing sufficient voltage with the engine running, the charge warning lamp turns OFF. If the charge warnin ...

Power supply and ground circuit
Combination meter Combination meter : diagnosis procedure Regarding Wiring Diagram information, refer to MWI-28, "Wiring Diagram". 1.Check fuses Check that the following fuses are not blown. Is the fuse blown? YES >> Replace the blown fuse after repairing the affected circu ...

Instrument lower panel lH
Removal and Installation REMOVAL Remove the instrument side finisher LH (1) using a suitable tool. Remove the hood and fuel filler handle assembly from the instrument lower panel LH. Refer to DLK-191, "FUEL FILLER OPENER CABLE : Removal and Installation". Release the ...

© 2014-2018 Copyright www.nisentra.com