S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: U1000 Can Comm Circuit

Av Control Unit

Dtc Description

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-Nissan Sentra vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Sentra vehicle, and each control unit shares information and links with other control units during operation (not independently). In CAN communication, control units are connected with 2 communication lines (CAN-High, CAN-Low) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U1000–01

CAN COMM CIRCUIT

(CAN COMM CIRCUIT)

Diagnosis condition

When ignition switch is ON.

Signal (terminal)

—

Threshold

—

Diagnosis delay time

—

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

Function of CAN communication signals received by AV control unit are inoperative

Dtc Confirmation Procedure

DTC Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Ignition switch ON.

      2. Ignition switch OFF and wait at least 30 seconds.

      3. Ignition switch ON and wait at least 30 seconds or more.

      4. Select “Self Diagnostic Result” mode of “MULTI AV”.

      5. Check DTC.

    Is DTC U1000–01 detected?

    YES>>

    Refer to DTC Diagnosis Procedure.

    NO>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO>>

    Confirmation after repair: Inspection End.

Diagnosis Procedure

Diagnosis Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE AGAIN

    1. CONSULT

      1. Ignition switch ON.

      2. Erase DTC.

      3. Perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.

    Is DTC detected again?

    YES>>

    Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

    NO>>

    Inspection End.

Bose Speaker Amp.

Dtc Description

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-Nissan Sentra vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Sentra vehicle, and each control unit shares information and links with other control units during operation (not independently). In CAN communication, control units are connected with 2 communication lines (CAN-High, CAN-Low) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U1000–01

CAN COMM CIRCUIT

(CAN COMM CIRCUIT)

Diagnosis condition

When ignition switch is ON.

Signal (terminal)

—

Threshold

—

Diagnosis delay time

—

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The system using the CAN communication signal from control unit which cannot communicate does not function

Confirmation Procedure

Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Ignition switch ON.

      2. Ignition switch OFF and wait at least 30 seconds.

      3. Ignition switch ON and wait at least 30 seconds or more.

      4. Select “Self Diagnostic Result” mode of “AUDIO AMP.”.

      5. Check DTC.

    Is DTC U1000–01 detected?

    YES>>

    Refer to DTC Diagnosis Procedure.

    NO>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO>>

    Confirmation after repair: Inspection End

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE AGAIN

    1. CONSULT

      1. Ignition switch ON.

      2. Erase DTC.

      3. Perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.

    Is DTC detected again?

    YES>>

    Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

    NO>>

    Inspection End.

    U0079 Control Module Communication Bus G Off
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0079–00 Control module communication Bus ...
    U1231 Amplifier Temperature
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1231–98 AMP TEMP (Amp temperature) — Di...

    Other materials:

    C161c-87 Steering Angle Sensor System
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...

    Combination Switch Output Circuit. Diagnosis Procedure
    Diagnosis Procedure Diagnosis Procedure CHECK OUTPUT 1 - 6 CIRCUIT FOR OPEN Ignition switch OFF. Disconnect BCM connector and combination switch connectors. ...

    Component Parts
    Engine Control System Component Parts Location Component Parts Location ENGINE ROOM COMPARTMENT Area behind left head lamp ...