Nissan Sentra B18 (2020-2025) Service Manual / Brakes / Brake Control System :: Vdc/tcs/abs / Dtc/circuit Diagnosis / U0073-00 Can Comm Circuit

Nissan Sentra B18 (2020-2025) Service Manual: U0073-00 Can Comm Circuit

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen item (Trouble diagnosis content)		DTC detection condition
U0073-00	Control module comm Bus A Off (Control module communication Bus A Off)	—	1	Diagnosis condition	When ignition switch is ON. When the power supply voltage is normal.
				Signal (terminal)	CAN communication signal
				Threshold	When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit).
				Diagnosis delay time	2 seconds or more
			2	Diagnosis condition	When ignition switch is ON. When the power supply voltage is normal.
				Signal (terminal)	CAN communication signal
				Threshold	When CAN communication signal is not continuously received from each control unit.
				Diagnosis delay time	2 seconds or more

POSSIBLE CAUSE

Note:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC	CRNT DTC
Harness or connector CAN communication line	CAN communication system

FAIL-SAFE

The following functions are suspended:

VDC function
TCS function
Brake assist function
Hill start assist function

Confirmation Procedure

Confirmation Procedure

PRECONDITIONING
1. If “Confirmation Procedure” has been previously conducted, always place the ignition switch in the OFF position and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
1. CONSULT
  1. Ignition switch OFF.
    Note:
    Wait at least 10 seconds after placing ignition switch in the OFF position.
  2. Start the engine.
    Note:
    Wait at least 10 seconds after start the engine.
  3. Select "Self Diagnostic Result" mode of "ABS".
Is DTC “U0073-00” detected?
YES >>
“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES >>
“PAST” is displayed: Inspection End. (Erase "Self Diagnostic Result" mode of "ABS".)
NO >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>
Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

 C1083-86 Steering Angle Sensor System

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen item (Trouble diagnosis content) DTC detection condition C1083-86 Steering angle sensor (Steering angl...

 U2156-87 Can Comm Circuit

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen item (Trouble diagnosis content) DTC detection condition U2156-87 CAN COMM err (steering angle sensor)...

Other materials:

Diagnosis System (distance Sensor)
Consult Function (laser/radar) CONSULT Function (LASER/RADAR) APPLICATION ITEMS CONSULT performs the following functions via CAN communication with ADAS control unit 2 and the communication with distance sensor. ...

U2152-87 Can Comm Err (adas Control Unit)
Dtc Description DTC Description DESCRIPTION CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Sentra vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan ...

Symptom Diagnosis. Rear View Monitor System
Rear View Monitor System Symptom Table Symptom Table REAR VIEW MONITOR SYSTEM Symptoms Check items Probable malfunction location ...