Wheel and Tire. Exploded View

Exploded View

1.

Wheel and tire

Removal and Installation

Removal and Installation

REMOVAL

Remove wheel cover (if equipped).

Remove wheel nuts using power tool. Refer to Exploded View.

Remove wheel and tire.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• When installing wheel nuts, tighten them diagonally by dividing the work two or three times in order to prevent the wheels from developing any distortion.

• Be careful not to tighten wheel nuts to a torque exceeding the specification to prevent strain on the disc brake rotor or brake drum.

• Use Genuine NISSAN wheel nuts.

Tire Pressure Sensor. Exploded View

Exploded View

1.	Tire pressure sensor	2.	Valve cap	3.	Valve core
4.	Valve	A.	Screw		: Parts that are replaced as a set when the tire is replaced.

Removal and Installation

Removal and Installation

REMOVAL

Remove the wheel and tire using power tool. Refer to Removal and Installation.

Remove the valve cap and the valve core to deflate the tire. Refer to Exploded View. Note:

If the tire is to be reused, apply a matching mark on the tire in line with the position of the valve hole in the wheel for the purpose of wheel and tire balance adjustment after installation.

Lubricate the tire outside bead well with a suitable non-silicone lubricant and separate the tire outside bead from the wheel.

CAUTION:

• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

• Do not damage the wheel.

Lubricate the tire inside bead well with a suitable non-silicone lubricant and separate the tire inside bead from the wheel.

CAUTION:

• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

• Do not damage the wheel.

Carefully lift and set the wheel and tire onto the tire changer turntable so that the tire pressure sensor (1) is at the bottom. Position the wheel and tire so that the tire pressure sensor is 270 degrees from the mounting/dismounting head (2).

CAUTION:

Do not damage the wheel.

Note:

To avoid damage to Nissan Sentra vehicle, the tire must not slip or spin on the wheel when dismounting, or mounting a tire’s outer bead. Damage to the wheel or the tire pressure sensor could result.

Remove the tire from the wheel.

Remove the screw and the tire pressure sensor from the valve.

CAUTION:

Do not drop or strike the tire pressure sensor. Replace the tire pressure sensor if it has been dropped from higher than one meter.

Cut the inner end (A) of the valve using a suitable tool (B).

CAUTION:

Do not damage the wheel.

Remove the valve (2) from the wheel (1) using Tool (A).

Tool (A) number

: NI-51980

CAUTION:

Do not damage the wheel.

INSTALLATION

Clean the valve hole in the wheel.

CAUTION:

Make sure there are no burrs, foreign substances, or indications of damage to the wheel.

Apply a suitable non-silicone lubricant to the surface of the valve (A) that touches the wheel and to the valve hole in the wheel.

CAUTION:

• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

• Do not allow lubricant to contact the air pressure detection hole (B).

Remove the valve cap from the new tire pressure sensor unit.

Position the valve (C) in the valve hole in the wheel (A).

CAUTION:

• Do not damage the tire pressure sensor.

• Do not allow lubricant to contact the air pressure detection hole (B).

• The tire pressure sensor must be oriented tangentially to the rim of the wheel.

Install the valve (2) to the wheel (1) using Tool (A).

Tool (A) number

: NI-51980

CAUTION:

• Do not drop or strike the tire pressure sensor. Replace the tire pressure sensor if it has been dropped from higher than one meter.

• Do not damage the wheel.

• Install the valve all the way to the wheel.

• Make sure the valve seats properly in the valve hole in the wheel.

• If the tire pressure sensor unit position is not correct, rotate the tire pressure sensor unit to the correct position using Tool.

Apply a suitable non-silicone lubricant to the tire inside bead.

CAUTION:

• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

• Do not allow lubricant to contact the air pressure detection hole.

Install the tire inside bead (1) onto the wheel (2) in the position shown.

CAUTION:

• Do not damage the wheel or the tire pressure sensor.

• Do not allow the tire beads to make contact with the tire pressure sensor.

Place the wheel on the turntable of the tire machine. Make sure that the tire pressure sensor (1) is 270 degrees from the mounting/dismounting head (2).

CAUTION:

Do not touch the tire pressure sensor with the mounting head.

Apply a suitable non-silicone lubricant to the tire outside bead.

CAUTION:

• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

• Do not allow lubricant to make contact with the tire pressure sensor.

Install the tire outside bead onto the wheel as normal.

CAUTION:

When installing, make sure that the tire does not rotate relative to the wheel.

Note:

• If the tire is being reused, align the matching mark applied on the tire with the position of the valve hole in the wheel for the purpose of wheel and tire balance adjustment after installation.

• To avoid damage to Nissan Sentra vehicle, the tire must not slip or spin on the wheel when dismounting, or mounting a tire’s outer bead. Damage to the wheel or the tire pressure sensor could result.

Inflate the tire. Refer to Tire Air Pressure.

Install the valve cap.

Balance the wheel and tire. Refer to Adjustment.

Install the wheel and tire in the appropriate position on the Nissan Sentra vehicle. Refer to Removal and Installation.

Perform the "ID REGISTRATION PROCEDURE". Refer to Description.

CAUTION:

For replacing the tire pressure sensor, the ID registration procedure must be performed.

Disposal

Disposal

CAUTION:

• When discarding tire pressure sensor, remove battery from tire pressure sensor.

• Dispose of battery according to the law and local regulations.

Remove battery (1) from tire pressure sensor. Note:

The battery is sealed to tire pressure sensor with urethane.

Remove urethane from tire pressure sensor.

Using a suitable tool, cut battery terminal (A), then remove battery from tire pressure sensor.

Tire Pressure Receiver. Removal and Installation. Removal and Installation

Removal and Installation

The Tire Pressure Receiver is an integral part of the BCM (Body Control Module). For removal of the Tire Pressure Receiver, refer to Removal and Installation.