S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: Power Supply and Ground Circuit (electric Intake Valve Timing Control Module)

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK FUSE

    1. Turn ignition switch OFF.

    2. Pull out 5 A fuse (No. 91) from IPDM E/R.

    3. Check that 5 A fuse is not blowing.

    Is the fuse blown (open)?

    YES >>

    Replace the fuse after repairing the applicable circuit.

    NO >>

    GO TO 2.

  2. CHECK FUSIBLE LINK

    1. Turn ignition switch OFF.

    2. Check that the following fusible link is not blowing.

      Fusible link No.

      Capacity

      F/L-I

      40A

    Is the fusible link blown (open)?

    YES >>

    Replace the fusible link after repairing the applicable circuit.

    NO >>

    GO TO 3.

  3. CHECK GROUND CONNECTION

    Check ground connection E9 and E15. Refer to Ground Inspection in Circuit Inspection.

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair or replace error-detected parts.

  4. CHECK ELECTRIC INTAKE VALVE TIMING CONTROL MODULE GROUND CIRCUIT

    1. Disconnect electric intake valve timing control module harness connectors.

    2. Check the continuity between electric intake valve timing control module harness connector and ground.

      Electric intake valve timing control module

      —

      Continuity

      Connector

      Terminal

      F80

      43

      Ground

      Existed

    3. Also check harness for short to power.

    Is the inspection result normal?

    YES >>

    GO TO 5.

    NO >>

    Repair or replace error-detected parts.

  5. CHECK ELECTRIC INTAKE VALVE TIMING CONTROL MODULE POWER SUPPLY

    1. Reconnect electric intake valve timing control module harness connectors.

    2. Check the voltage between electric intake valve timing control module harness connector terminals as follows.

      Electric intake valve timing control module

      Voltage

      Connector

      +

      −

      Terminal

      F80

      47

      43

      Battery voltage

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Perform trouble diagnosis for power supply circuit.

  6. CHECK IGNITION SWITCH SIGNAL

    Check the voltage between electric intake valve timing control module harness connectors as follows.

    Electric intake valve timing control module

    Condition

    Voltage

    +

    −

    Connector

    Terminal

    Terminal

    F80

    39

    43

    Ignition switch: ON

    Battery voltage

    Ignition switch: OFF

    0 V

    Is the inspection result normal?

    YES >>

    Check intermittent incident. Refer to Intermittent Incident.

    NO >>

    GO TO 7.

  7. CHECK IGNITION SWITCH SIGNAL

    1. Turn ignition switch OFF.

    2. Disconnect electric intake valve timing control module harness connectors.

    3. Disconnect IPDM E/R harness connector.

    4. Check the continuity between IPDM E/R harness connector and electric intake valve timing control module harness connector.

      IPDM E/R

      Electric intake valve timing control module

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      E43

      19

      F80

      39

      Existed

    5. Also check harness for short to power and short to ground.

    Is the inspection result normal?

    YES >>

    Perform trouble diagnosis for power supply circuit.

    NO >>

    Repair or replace error-detected parts.

    Power Supply and Ground Circuit (ecm)
    Diagnosis Procedure Diagnosis Procedure CHECK THE BATTERY CABLE Turn ignition switch OFF. Check the battery cable for tightening enough. Note: Check the continuity between the b...
    Refrigerant Pressure Sensor
    Component Function Check Component Function Check CHECK REFRIGERANT PRESSURE SENSOR FUNCTION Start engine and warm it up to normal operating temperature. Turn A/C switch and blo...

    Other materials:

    Abs Warning Lamp
    Component Function Check Component Function Check CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for 1 second after ignition switch is placed ON. CAUTION: Never start th ...

    Manifold Absolute Pressure Sensor
    Component Inspection Component Inspection CHECK MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR-1 Turn ignition switch OFF. Start engine and warm it up to normal operating temperature. Turn ...

    Driver Assistance Buzzer Circuit
    Component Function Check Component Function Check CHECK DRIVER ASSISTANCE BUZZER CONSULT Select “ADAS buzzer 2” in “Active Test” mode of “ICC/ADAS 2”. Check that the function operates ...