Nissan Sentra Service Manual: P2119 Electric throttle control actuator

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P2119 Electric throttle control actuator

DTC Logic

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition		Possible cause
P2119	ETC ACTR-B1 (Throttle actuator control throttle body range/ performance)	A	Electric throttle control actuator does not function properly due to the return spring malfunction.	Electric throttle control actuator
		B	Throttle valve opening angle in fail-safe mode is not in specified range.
		C	ECM detect the throttle valve is stuck open.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B

Turn ignition switch ON and wait at least 1 second.
Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
Set selector lever to P (CVT) or Neutral (M/T) position
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON and wait at least 1 second.
Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
Set selector lever to P (CVT) or Neutral (M/T) position.
Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
Check DTC.

Is DTC detected? YES >> Proceed to EC-430, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C

Turn ignition switch ON and wait at least 1 second.
Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
Set selector lever to P (CVT) or Neutral (M/T) position.
Start engine and let it idle for 3 seconds.
Check DTC.

Is DTC detected? YES >> Proceed to EC-430, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

Remove the intake air duct. Refer to EM-25, "Exploded View".
Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal? YES >> Replace electric throttle control actuator. Refer to EM- 27, "Removal and Installation".

NO >> Remove the foreign matter and clean the electric throttle control actuator inside, then perform throttle valve closed position learning. Refer to EC-139, "Work Procedure".

P2122, P2123 APP Sensor

P2118 Throttle control motor

DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P2118 ETC MOT-B1 (Throttle actuator co ...

P2122, P2123 APP Sensor

DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-353, "DTC Logic". DTC No ...

Other materials:

Trouble diagnosis - specification value
Description The specification (SP) value indicates the tolerance of the value that is displayed in вЂњSPECвЂќ of вЂњDATA MONITORвЂќ mode of CONSULT during normal operation of the Engine Control System. When the value in вЂњSPECвЂќ of вЂњDATA MONITORвЂќ mode is within t ...

B0020 Side airbag module LH
Description DTC B0020 FRONT LH SIDE AIR BAG MODULE The front LH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the front LH side air bag module. PART LOCATION Refer to SRC-5, " ...

Map lamp
Removal and installation Removal Lower front edge of map lamp (1) down from the headlining by releasing the metal clips, then slide forward to clear pawls at rear. : Metal clip Pawl Disconnect the harness connectors from the map lamp and remove. Installation Installation is in t ...