Nissan Sentra Service Manual: P1715 Input speed sensor

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P1715 Input speed sensor

Description

ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control.

DTC Logic

DTC DETECTION LOGIC

NOTE:

If DTC P1715 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
If DTC P1715 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335. Refer to EC-277, "DTC Logic".
If DTC P1715 is displayed with DTC P0340, first perform the trouble diagnosis for DTC P0340. Refer to EC-280, "DTC Logic".
If DTC P1715 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to EC-348, "DTC Logic".
If DTC P1715 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer to EC-350, "DTC Logic".

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition	Possible cause
P1715	IN PULY SPEED (IN PULY SPEED)	Input speed sensor signal is different from the theoretical value calculated by ECM from output speed sensor signal and engine rpm signal.	Harness or connectors (The CAN communication line is open or shorted) Harness or connectors (Input speed sensor circuit is open or shorted) TCM

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

Start engine and drive the vehicle at more than 50 km/h (31 MPH) for at least 5 seconds.

CAUTION:

Always drive vehicle at a safe speed.

Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-406, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC WITH TCM

Check DTC with TCM. Refer to TM-108, "CONSULT Function".

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform trouble shooting relevant to DTC indicated.

2.REPLACE TCM

Replace TCM. Refer to TM-263, "Removal and Installation".

>> INSPECTION END

P1652 Starter motor system comm

Description ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R via BCM by CAN communication. Under normal ...

P1800 Intake manifold tuning valve

DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P1800 VIAS S/V-1 (Variable intake air ...

Other materials:

Front combination lamp
Exploded view Large cover (not serviceable) Small cover (not serviceable) Front combination lamp Halogen lamp bulb (high beam) Turn signal lamp bulb Turn signal lamp bulb socket LED harness connector Halogen lamp bulb (high beam) harness connector Halogen lamp bulb (low b ...

Electric oil pump
Exploded View Transaxle assembly Electric oil pump sub harness O-ring Electric oil pump and motor assembly CVT fluid Removal and Installation REMOVAL Remove neighboring parts of electric oil pump. Remove electric oil pump sub harness. Remove electric oil pump and motor a ...

Brake master cylinder
Exploded View Reservoir cap Oil strainer Reservoir tank Cylinder body Pin O-ring Grommet Apply brake fluid PBC (Poly Butyl Cuprysil) grease or silicone-based grease Removal and Installation REMOVAL CAUTION: Do not spill or splash brake fluid on painted surfaces. ...