Nissan Sentra B18 (2020-2025) Service Manual: P10c9 Internal Control Module Fuel Injector

Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P10c9 Internal Control Module Fuel Injector

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P10C9	Internal control module fuel injector (Internal control module fuel injector)	Diagnosis condition	—
		Signal (terminal)	—
		Threshold	Direct injector driver unit is malfunctioning. ECM detects No. 2 injector circuit is shorted.
		Diagnosis delay time	—

POSSIBLE CAUSE

Harness or connectors
- Direct fuel injector circuit is open
Battery power supply
ECM (Direct injector driver unit)
Direct fuel injector

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Traveling control mode	Accelerator angle variation control	ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction. Note: ECM does not control the accelerator pedal releasing speed.
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
- Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 20 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DIRECT FUEL INJECTOR

Check direct fuel injector. Refer to Component Function Check.

Is inspection result normal?
YES >>
GO TO 2.
NO >>
Repair or replace error-detected parts.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
4. Check 1st trip DTC.
Is the DTC displayed again?
YES >>
Replace ECM. Refer to ECM : Removal & Installation.
NO >>
INSPECTION END

P10c8 Internal Control Module Fuel Injector

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

P10ca Internal Control Module Fuel Injector

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

Other materials:

Cvt Shift Selector (detent Switch)
Component Inspection Component Inspection CHECK CVT SHIFT SELECTOR (DETENTION SWITCH) Ignition switch OFF. Disconnect CVT shift selector (detent switch) connector. ...

Door Assembly
Removal and Installation Removal and Installation CAUTION: Use two people when removing or installing the front door due to its heavy weight. When removing and installing front door assembly, support front door with a suitable too ...

Wiring diagram
Meter system Wiring diagram Compass Wiring diagram ...