Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0326 Knock Sensor

Nissan Sentra B18 (2020-2025) Service Manual: P0326 Knock Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC		CONSULT screen terms (Trouble diagnosis content)	DTC detected condition
P0326	00	KNOCK SENSOR 1 B1 (Knock/Combustion Vibration Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor)	Diagnosis condition	During fuel cut after engine warm-up
			Signal	Knock sensor
			Threshold	When the ECM detects knocking during engine running more than the threshold value
			Diagnosis delay time	5 seconds

POSSIBLE CAUSE

Harness or connectors

(The knock sensor circuit is open or shorted.)

Knock sensor
Knock sensor installation

FAIL-SAFE

Not applicable

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0326 is displayed with DTC P0327 or P0328, first perform the confirmation procedure (trouble diagnosis) for DTC P0327 or P0328.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description or DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and warm it up to normal operating temperature.
2. Revving engine from idle up to 3,000 rpm quickly.
3. Repeat the step 2 at 10 times.
4. Check DTC.
Is DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0326 is displayed with DTC P0327 or P0328, first perform the confirmation procedure (trouble diagnosis) for DTC P0327 or P0328.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description or DTC Description.
NO >>
GO TO 2.
CHECK INSTALLATION CONDITION OF KNOCK SENSOR

Visually check that the knock sensor is installed normally.

Is the inspection result normal?
YES >>
GO TO 3.
NO >>
Repair or replace error-detected parts.
CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?
YES >>
GO TO 4.
NO >>
Repair or replace error-detected parts.
CHECK KNOCK SENSOR CIRCUIT

Check knock sensor circuit. Refer to DTC Diagnosis Procedure.

Is the inspection result normal?
YES >>
GO TO 5.
NO >>
Repair or replace error-detected parts.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to DTC Description.
Is the 1st trip DTC P0326 displayed again?
YES >>
Replace ECM. Refer to Removal & Installation.
NO >>
INSPECTION END

 P0315 Ckp Sensor (pos)

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0315 Crankshaft position (Crankshaft Position S...

 P0327 Ks

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0327 KNOCK SEN/CIRC-B1 (Knock sensor 1 circuit ...

Other materials:

Cvt Fluid Temperature Sensor
Exploded View Exploded View Transaxle assembly Reduction gear assembly ...

Vehicle-to-vehicle distance control mode limitations
WARNING Listed below are the system limitations for the Intelligent Cruise Control (ICC) system. Failure to operate the Nissan Sentra in accordance with these system limitations could result in serious injury or death. The ICC system is primarily intended for use on straight, dry, open road ...

Component Parts. Door & Lock System
Door & Lock System Component Parts Location Component Parts Location A View with CVT shift selector B Left side of instrument ...