Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: Optical Sensor Circuit

Nissan Sentra B18 (2020-2025) Service Manual / Driver Controls / Exterior Lighting System :: Led Headlamp / Dtc/circuit Diagnosis / Optical Sensor Circuit

Component Function Check

Component Function Check

  1. CHECK OPTICAL SENSOR SIGNAL

      1. Ignition switch ON.

      2. Turn lighting switch AUTO.

      3. With the optical sensor illuminating, check the exterior lamps status.

        Condition

        Exterior lamp status

        Optical sensor

        When illuminating

        Turns OFF

        When shutting off light

        Turns ON

    Is the inspection result normal?

    YES >>

    Optical sensor circuit is normal.

    NO >>

    Refer to Diagnosis Procedure.

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK OPTICAL SENSOR POWER SUPPLY

      1. Ignition switch ON.

      2. Turn lighting switch AUTO.

      3. Check voltage between optical sensor harness connector and ground.

        +

        -

        Voltage

        (Approx.)

        Optical sensor

        Connector

        Terminal

        M72

        1

        Ground

        5 V

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    GO TO 5.

  2. CHECK OPTICAL SENSOR GROUND

      1. Disconnect optical sensor connector

      2. Check continuity between optical sensor harness connector and ground.

      Optical sensor

      —

      Continuity

      Connector

      Terminal

      M72

      3

      Ground

      Yes

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 7.

  3. CHECK OPTICAL SENSOR SIGNAL

      1. Connect optical sensor connector.

      2. Check voltage between optical sensor harness connector and ground.

      +

      -

      Voltage

      (Approx.)

      Optical sensor

      Connector

      Terminal

      M72

      2

      Ground

      0.1 – 4.4 V

    Is the inspection result normal?

    YES >>

    GO TO 8.

    NO >>

    GO TO 4.

  4. CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)

      1. Ignition switch OFF.

      2. Disconnect optical sensor connector and BCM connector M84.

      3. Check continuity between optical sensor harness connector and ground.

      Optical sensor

      —

      Continuity

      Connector

      Terminal

      M66

      2

      Ground

      No

    Is the inspection result normal?

    YES >>

    Replace optical sensor. Refer to Removal and Installation.

    NO >>

    Repair or replace harness.

  5. CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)

      1. Ignition switch OFF.

      2. Disconnect optical sensor connector and BCM connector.

      3. Check continuity between optical sensor harness connector and BCM harness connector.

        Optical sensor

        BCM

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M72

        1

        M84

        28

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 6.

    NO >>

    Repair or replace harness.

  6. CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)

    1. Check continuity between optical sensor harness connector and ground.

      Optical sensor

      —

      Continuity

      Connector

      Terminal

      M72

      1

      Ground

      No

    Is the inspection result normal?

    YES >>

    Replace BCM. Refer to Removal and Installation.

    NO >>

    Repair or replace harness.

  7. CHECK OPTICAL SENSOR GROUND CIRCUIT

      1. Ignition switch OFF.

      2. Disconnect optical sensor connector and BCM connector.

      3. Check continuity between optical sensor harness connector and BCM harness connector.

        Optical sensor

        BCM

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M72

        3

        M84

        29

        Yes

    Is the inspection result normal?

    YES >>

    Replace BCM. Refer to Removal and Installation.

    NO >>

    Repair or replace harness.

  8. CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN)

      1. Ignition switch OFF.

      2. Disconnect optical sensor connector and BCM connector.

      3. Check continuity between optical sensor harness connector and BCM harness connector.

        Optical sensor

        BCM

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M72

        2

        M84

        8

        Yes

    Is the inspection result normal?

    YES >>

    Replace BCM. Refer to Removal and Installation.

    NO >>

    Repair or replace harness.

Back-Up Lamp Relay Circuit
Component Function Check Component Function Check CHECK BACK-UP LAMP OPERATION Ignition switch ON. ...

Hazard Switch Circuit
Component Function Check Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. ...

Other materials:

Component Parts
Cvt Control System Component Parts Location Component Parts Location Shifter assembly Transaxle assembly Pedal periphery a ...

Dtc Diagnosis Procedure
DTC Diagnosis Procedure Note: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported ...

Front wiper motor lo circuit
Component function check 1. Check front wiper lo operation Ipdm e/r auto active test Start ipdm e/r auto active test. Refer to pcs-9, "diagnosis description" (with intelligent key system) or pcs-37, "diagnosis description" (without intelligent key system). Check tha ...

© 2014-2026 Copyright www.nisentra.com