S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: Main Line Between Abs and M&a Circuit

Diagnosis Procedure

Diagnosis Procedure

  1. CHECK CONNECTOR

    1. Turn the ignition switch OFF.

    2. Disconnect the battery cable from the negative terminal.

    3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

      • Harness connector E4

      • Harness connector M2

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    Repair the terminal and connector.

  2. CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

    1. Disconnect the following harness connectors.

      • ABS actuator and electric unit (control unit)

      • Harness connectors E4 and M2

    2. Check the continuity between the ABS actuator and electric unit (control unit) harness connector and the harness connector.

      ABS actuator and electric unit (control unit) harness connector

      Harness connector

      Continuity

      Connector No.

      Terminal No.

      Connector No.

      Terminal No.

      E33

      11

      E4

      55G

      Existed

      10

      54G

      Existed

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Repair the main line between the ABS actuator and electric unit (control unit) and the harness connector E4.

  3. CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

    1. Disconnect the connector of combination meter.

    2. Check the continuity between the harness connector and the combination meter harness connector.

    Harness connector

    Combination meter harness connector

    Continuity

    Connector No.

    Terminal No.

    Connector No.

    Terminal No.

    M2

    55G

    M24

    18

    Existed

    54G

    19

    Existed

    Is the inspection result normal?

    YES (Present error) >>

    Check CAN system type decision again.

    YES (Past error) >>

    Error was detected in the main line between the ABS actuator and electric unit (control unit) and the combination meter.

    NO >>

    Repair the main line between the harness connector M2 and the combination meter.

    Malfunction Area Chart
    Vehicle Can Communication 1 Circuit Vehicle CAN Communication 1 Circuit MAIN LINE Malfunction area Reference Main line between ABS actuator and electric unit (control unit) and ...
    Main Line Between Icc 2 and Rdr-L Circuit
    Diagnosis Procedure Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and ...

    Other materials:

    Symptom Diagnosis
    The Fuel Gauge Indicator Does Not Operate Description Description Fuel gauge will not indicate from a certain position. Diagnosis Procedure Diagnosis Procedure PERFORM COMBINATION METER SELF-DIAGNOSIS MODE Perform the self-diagnosis mode ...

    Normal Operating Condition
    Symptom Description Symptom Description FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED) If the status of that the engine speed is above 2,500 rpm under no load (at 0 km/h and the selector lever position is P or N) takes more than the specified time, fuel will be cut off after s ...

    Uniform tire quality grading
    DOT (Department of Transportation) Quality Grades apply to all passenger car tires and are intended to provide comparative information in addition to meeting federal safety requirements. Where applicable, these quality grades are molded into the tire sidewall between the tread shoulder and th ...