Nissan Sentra manuals

Toyota Camry Owner's Manual (2023): If you have a flat tire

Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire.

WARNING

■If you have a flat tire

Do not continue driving with a flat tire.

Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair, which could result in an accident.

Before jacking up the vehicle

Location of the spare tire, jack and tools

2WD models

Steps to take in an emergency

AWD models

Steps to take in an emergency

  1. Luggage floor cover
  2. Wheel nut wrench
  3. Jack
  4. Spare tire
  5. Jack handle
  6. Wheel lock key (if equipped)

WARNING

■Using the tire jack

Observe the following precautions.

Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury.

NOTICE

■To prevent damage to the vehicle when using a jack

When jacking up the rear of the vehicle, make sure not to position the jack under the bracket shown in the illustration near the rear jack point, as the vehicle body may be damaged.

Steps to take in an emergency

Wheel lock nut (if equipped)

When replacing tires on a vehicle with wheel lock nuts, use the following procedures to remove and install the wheel lock nuts. The wheel lock key is stored in the tray inside the luggage compartment. Always return the wheel lock key to its original position after use, so that it does not get lost.

■ Removal

For ease of removal, the wheel lock nut should always be the first one loosened.

1. Place the wheel lock key on top of the wheel lock nut, turning until the wheel lock key and wheel lock nut patterns engage.

2. Place the wheel nut wrench on the wheel lock key, and while applying pressure on the wheel lock key, loosen the wheel lock nut.

■ Installation

For ease of installation, the wheel lock nut should always be the last one tightened.

1. By hand, install a wheel lock nut on the wheel to be installed.

2. Place the wheel lock key on top of the wheel lock nut, turning until the wheel lock key and wheel lock nut patterns engage.

3. Place the wheel nut wrench on the wheel lock key, and while applying pressure on the wheel lock key, tighten the wheel lock nut to the recommended torque.

NOTICE

■When using a wheel lock key

Do not use an impact wrench. Using an impact wrench may cause permanent damage to wheel lock nut and wheel lock key. If in doubt about wheel lock application, contact your Toyota dealer.

Taking out the jack

1. Lift up the hook of the luggage floor cover on the trunk floor.

Steps to take in an emergency

2. Secure the luggage floor cover using the hook provided.

Steps to take in an emergency

3. Remove the jack.

2WD models

2WD models

AWD models

Steps to take in an emergency

If a warning message is displayed
The multi-information display shows warnings of system malfunctions, incorrectly performed operations, and messages that indicate a need for maintenance. When a message is shown, perform the correc ...

Taking out the spare tire
1. Lift up the hook of the luggage floor cover on the trunk floor. 2. Secure the luggage floor cover using the hook provided. 3. Remove the tool tray. 2WD models AWD models 4. Loosen th ...

Other materials:

Precaution for supplemental restraint system (SRS) "air bag" and "seat belt pre-tensioner"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system ...

Rear window defogger switch
Description The rear window defogger is operated by pressing the rear window defogger switch ON. The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is on. Component function check 1. Check rear window defogger switch function Check ( ...

Dlc branch line circuit
Diagnosis procedure 1.Check connector Turn the ignition switch off. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the data link connector for damage, bend and loose connection (connector side and harness side). Is the inspection resul ...

© 2014-2023 Copyright www.nisentra.com